24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for User Interface by Whirlpool

  1. Our Price $104.74
    Compare At $125.69
    You Save $20.95
     
    • Part Number: AP3177796
    • MFG Part Number: 8531262
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool User Interface (Part Number: AP3177796)

Ask a Question

Most Interesting  |  Latest Questions

All the green lights on the left of the control panel light properly. The start button does not light and the dishwasher will not start. We did power cycle the dishwasher, this had no effect.

Jack

Answer

Was this helpful?

1 Answer

Dishwasher will not start. The last time it ran a full cycle but did not drain all the water out. When I started again it ran but still did not drain all the water. Now it will not start at all. The green LED lights come on excluding the start LED. The Led lights stay on for several seconds and then turn off.I replaced the ribbon cable and the door switch and that did not fix the problem. What do you think the problem is? Thanks

Vernon T. for Model Number KUDP01FLSS1

Answer

Was this helpful?

1 Answer

My clean button is blinking and will not turn off when I push cancel, I try to run a cycle to clean and none of the buttons will stay lit for more than 2 seconds... when I push start the machine will run... is my panel bad, what part do I need to replace??

Vgrace for Model Number kudpoiflss6

Answer

Was this helpful?

1 Answer

I guess I don't understand what a difference changing the wires of the fuse would make. Can you call me at 800-496-3287 ?

David P. for Model Number KUDP01FLSS1 KITCHEN AID

Answer

Was this helpful?

1 Answer

I did NOT change the wires with the fuse, only the fuse thinking it wouldn't make any difference. The dishwasher worked afterwards and I ran several washes. Only upon trying the LIGHT CHINA cycle did the problem start over again and the fuse went out leaving a cycle undoNE and water in the tub. I played with it again this morning and I do not hear any relay switch clicking like I thought I did yesterday. It is totally dead. The fact that there is water in the tub leads me to think that the drain pump or something related is causing the fuse to short out, but those parts aren't related to the LIGHT CHINA setting and the fact that it doesn't work. I'm baffled.

David P. for Model Number KUDP01FLSS1 KITCHEN AID

Answer

Was this helpful?

1 Answer

Replaced the fuse per your recommendation. Panel lights came back on and cycles run, except the light china cycle, so I replaced the user interface board. Light china cycle light came on when pushed one time but something has now shorted out again. Water in the tub bottom, no lights, BUT I do hear a relay switch clicking when buttons are selected. What should I try next?

David P. for Model Number KUDP01FLSS1 KITCHEN AID

Answer

Was this helpful?

1 Answer

We had the same problem as the other people listed above, non blinking lights when the start button is hit, but now the whole panel has gone dark as if there is no power at all. There's water in the basin of the dishwasher that indicates this power problem struck mid cycle at one point.

David P. for Model Number KUDP01FL

Answer

Was this helpful?

1 Answer

We have the start problem where the lights don't blink when the start button is pressed. I think it would be easier to just replace the entire control panel, but does the control panel part include the user interface part or do I need to purchase these separately?

Kevin G. for Model Number KUDPO1FLSS6

Answer

Was this helpful?

1 Answer

I have the problem of the dishwasher not starting because the lights don't blink when I press the start button on the control panel. Do I most likely need an entire new control panel. Does that come with the electronic control or do I just need to replace the electronic control?

Marcia G. for Model Number KUDPO1FLSS6

Answer

Was this helpful?

1 Answer

Like others we have issues starting the dishwasher because the control panel lights won't blink. They come on but won't blink if I hit start the problem has been getting worse and worse. Will replacing the interface help this

Frank

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify