No cold water coming out from inlet valve.
Answer Hello Joel. You will need to check and see if power is coming to the cold valve. If there is power there, and the cold water is not working, you will need to replace the valve. Hope this helps.
1 person found this answer helpful.
i test the leeds on the solonoids and on my didital tester it reads .842 is that means the valve bad ?????
The reading that you get would depend on the setting that you have it set for and if it is an auto range. If it is auto range then it does sound like the resistance would be within range.
Machine doesn't rinse on any cycle. Would changing valve #w10144820, maybe be my solution?
Answer Hello Cjsand. If the cold water is not filling, and there is power to the valve, then the valve would fix the issue. If the cold water works, then it cold be the lid switch or a bad timer.
No cold water only hot on setting requiring hot water. Tub will not fill completely unless on Hot. Rinse cycle will not work because it uses cold water. Tub fills completely on hot setting but still no rinse cycle because it requires cold water I am told. Cold water Hose has screen filter and works (Flows readily) when not attached to washer. How do I access the valves that need replacing if that is what it takes and what is the part #? Could it be the automatic temperature sensor.
You will want to check the screens on the inlet valve to make sure that they are not clogged. Also check the power to the water valve to ensure that there is power getting to it. If there is no power getting to the valve then the temp switch would most likely be the cause of failure. To access the water valve you will need to remove the control panel. The control panel can be removed by using a putty knife under the front corners of the control and pushing in on a spring clip to release the panel. Under the control panel there will be 2 clips that you would remove. Once removed you can move the cabinet to access the valve.
Water continues to fill after washer has completed its cycle.
With the unit continuing to fill with water when the unit is shut off then the water valve would be the issue and would need to be replaced.
When I start the washer, only hot water comes out, so I think the cold water inlet valve is not working. Is there a video or instructions on how to get access to the valve to replace it. I called a repairman and he wants from $185.00 to $225.00 to replace it and with instructions how to get to the valve I can do it for just the price of the valve. Thank you
Answer Hello Roger. 1. Unplug washer or disconnect power. (also disconnect the fill hoses) 2. Slide a putty knife under the right or left corner of the control panel. Lift the corner of the panel and push back on the knife blade to release the clip. Repeat the procedure for the other clip. 3. Rotate the control panel and position it back out of the way. 4.Lift the locking tab, and disconnect the main harness from the lid switch connector. 5.Remove the 5/16? hex-head screw from the green ground wire on the lid switch. Lift the washer lid so it is straight up. Release the locking tab and pull the lid switch up and out of the cabinet top opening. 6. Use a screwdriver and unclip the left and right cabinet spring clips from the cabinet top. 7. Rotate the cabinet up in the back and slide forward so you can access the top of the tub, and set the cabinet aside." You now have access to the fill valve assembly Use a flat blade screw driver and remove the plastic mounting pin, and disconnect the tabs in the assembly from the slots in the cabinet back, disconnect the wires and reverse the procedure to install the new valve assembly.
The machine keeps filling up with water.It doesent over flow. The water stays on and must just drain out .I don't hear the pump running.The pump will pump out the water if you turn the dial .I tried all the water height settings it does the same thing on all of them, although I did get it to work once on small load. It just never fills up
Answer Ken, You need to check and make sure the top of the drain pipe is at least 38 inches high from the floor level. And make sure the drain hose is not "forced" down into the pipe or taped and sealed off to the pipe. Right at this point, it sounds like you have a "syphon" effect on the drain, because the pipe is too low, or there is no vent air to the drain because the hose is taped/sealed to the pipe.