24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Water Inlet Valve by Whirlpool

  1. Our Price $82.45
    Compare At $98.12
    You Save $15.67
     Watch Video
    • Part Number: AP3040319
    • MFG Part Number: 2206123
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Water Inlet Valve (Part Number: AP3040319)

Ask a Question

Most Interesting  |  Latest Questions

I have taken out the three solenoid valve,but don't know how the wiring goes to plug onto the prongs.The plugs have 2 wires on 1 side and 1 wire on the other. The plugs are colorred,purple, red and white. On the solenoid has a marking "M " and "B4" on the prongs. Please tell me how they connect. Your help would be very appericated.

Norman Y. for Model Number ED25TEXHW01

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

I have replaced the old inlet water valve and replaced with Part #2206123. Water dispenser is now working which is good. However, now when ice maker cycles on water comes out the water dispenser. Help!

Tim for Model Number Model #106.50532101

Answer

Was this helpful?

1 Answer

I have installed a new water inlet valve (part #2206123) on the Kenmore Model #59212990. However I still have the same problem, no water coming out of the water dispenser on the door. Before I installed the new valve, I had water going to the ice maker just fine, not sure now. I know that there are two connections for a 1/4 hose and 2 connections for 5/16 line, can you tell me which hose goes where. From the videos that I have watched it looks like the 1/4 hose that comes down the back of the refrigerator goes on the bottom 1/4 connection. Is that correct?

Clark for Model Number 59212990

Answer

Was this helpful?

1 Answer

I replaced ice maker(106 626662), filter and the inlet valve (2206123)on my Kenmore side-by-side(106.53504300). I still am not getting water coming into the cube tray. I was vary careful to put all the electrical and waterlines on as they came off the old one. Water does flow through fine to the water despenser. Is there some way to reset it so it will work as intended?

Denny for Model Number 106.53504300

Answer

Was this helpful?

1 Answer

Icemaker not making ice. Sometimes little water and sometimes it over flows. You can hear when water shuts off it makes a loud noise. Is it the water intake value?

Vanessa for Model Number Estate Fridge TS22AE

Answer

Was this helpful?

1 Answer

I'm getting too much water when the ice maker fills up. When I adjust the timer, it doesn't change the length of time it fills. I'm thinking the ice maker is bad but I'm not sure. I've also checked the water inlet valve. How many ohms should water inlet valve #2206123 be pulling? I'm getting. The inlet solenoid is pulling 350, the green solenoid is pulling 175, and the purple is pulling 350. Does this mean the inlet valve is good? The water pressure going into the inlet valve seems to be fine. I've read through research that whenever you get too much water, it is either the ice maker, the water inlet valve, or the pressure coming in.

Jeff for Model Number 10653502300

Answer

Was this helpful?

1 Answer

After replacement inlet water valve I have water dipenser working fine but in plastic pipe what going to the top of refrigerator I don'tse water coming. Maybe I didn't connect properly.where I can see where I need connect that plastic pipe.

Sanja V for Model Number Part 2206123

Answer

Was this helpful?

1 Answer

I'm looking at the Water Inlet Valve. Your video says replace it if water is NOT coming into the water spout or the ice maker. My problem is that the water is coming in but will not turn off sometimes -- so there is leaking from the water spout in the door (not a lot and not always) and the water will build up into the shoot of the icemaker and then freeze so that it will not make ice again until I thaw that tubing out. Is that problem of the water not shutting off at the right time from the Water Inlet Valve also, or should I be looking at some other part? Thank you!!

Dave F. for Model Number Whirlpool Refrigerator ED25TE

Answer

Was this helpful?

1 Answer

Hello- I need a gasket for inlet valve right where the copper line connects to the inlet valve. Is this for sale? Thank you.

Edgar for Model Number ED25TEX

Answer

Was this helpful?

1 Answer

I recently replaced the three solenoid water valve on the fridge to solve an ice maker problem. The only problem I can detect in the old unit is an open winding reading in the one solenoid that opens the valve to the ice maker tray. There are three plastic solenoids of different colors, red on the inlet valve, blue on the water dispenser valve and green on the ice maker valve. Are these individual solenoids available? All they appear to be is a winding encased in plastic with two terminals. valve is a FSP Model X74 part no.2206123

J.e.jones for Model Number ED5GTFXKQ00

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify