Door Boot Seal

Kendall for Model Number WF210ANW/XAA

Answer Hello Kendall. Based on the part number you provided, DC64-00802A is the correct boot seal. 

Ashley for Model Number Samsung VRT Steam Washer WF419AAW/XAA01

Answer Hello Ashley. Based on the model number you provided, DC97-14932B is the correct door gasket and should be all you need if the clamps are good for the boot. 

Gregory for Model Number WF337AAL

Answer Hi Gregory. The door boot seal part # DC64-00802A does not come with the placement ring part # u0038. Thank You. 

Julie for Model Number WF218ANW

Answer Hi Julie. Here is the information from the manufacturer. Hope this helps! Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB): 1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover. 2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button. 3. Press the Separate button to separate the Detergent Box. 4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it. (Take care not to damage the Hook) 5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB. Seperate Sub-PCB from Main-PCB. 1. Pull the Diaphragm while holding the inside of the diaphragm with your hands. 2. Remove the 3 screws to separate the switch. 3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame. To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole. 4. Push the lever and lift it up slightly to open the Front Cover. 5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red). 6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame. 7. Remove the clamp from the back of the door boot. 8. Reinstall in reverse order. Thank You. 

Julie for Model Number WF218ANW

Answer Hello Julie. Here is the information from the manufacturer. Hope this helps! Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB): 1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover. 2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button. 3. Press the Separate button to separate the Detergent Box. 4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it. (Take care not to damage the Hook) 5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB. Seperate Sub-PCB from Main-PCB. 1. Pull the Diaphragm while holding the inside of the diaphragm with your hands. 2. Remove the 3 screws to separate the switch. 3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame. To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole. 4. Push the lever and lift it up slightly to open the Front Cover. 5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red). 6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame. 7. Remove the clamp from the back of the door boot. 8. Reinstall in reverse order. Good Luck!! 

Jacque P. for Model Number wf218anw/xaa door seal part # dc64-00802a

Answer Hello Jacque! Here is the information from the manufacturer, hope they help! Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB): 1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover. 2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button. 3. Press the Separate button to separate the Detergent Box. 4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it. (Take care not to damage the Hook) 5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB. Seperate Sub-PCB from Main-PCB. 1. Pull the Diaphragm while holding the inside of the diaphragm with your hands. 2. Remove the 3 screws to separate the switch. 3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame. To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole. 4. Push the lever and lift it up slightly to open the Front Cover. 5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red). 6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame. 7. Remove the clamp from the back of the door boot. 8. Reinstall in reverse order.