Whirlpool W10184148 Atc Switch Mid Level

Total
$0.00

Part Number:	AP4358828
MFG Part Number:	W10184148
Made by:	Whirlpool

Our Price
$39.80
Regularly	You Save
~~$50.59~~	$10.79

Most Interesting

While washing a load of towels the agitator stopped and the water won't drain. Is there a reset button / switch somewhere? Does it sound like the motor burned out?

Jeanine for Model Number RTW440XQ0 serial# c20440891

Answer Hello Jeanine. You need to check and see if the lid switch is broke on the unit and needs to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Roper washer. The washer is not letting enought hot water into the basin. It lets a little amount of hot water in but it also lets in about twice as much cold water. I checked the hoses and switched them around and the opposite happened. I was thinking it was probably the valves or the atc switch?

Aaron for Model Number RTW4440XQ0

Answer Hello Aaron. This is the way this model is designed to do. It has a thermistor built into the water valve W10144820.

Was this helpful?

I have two questions please... first. My admiral washing machine only works on regular and only partly works on perm/gentle. and not at all on Gentle and blows the circuit on hand wash.. is this problem isolated to the selector alone and can this part be purchased? Secondly, my ATC seems to be having issues.. on warm it fills only hot and does not work on the other two settings.. however on the regular temp settings it seems to fill in the propper temps.

Phil S for Model Number 4755AWW

Answer Phil, A complete and proper model number would be a big help, But, the ATC switch W10184148 does control the water temperature, and the water temperature issue is most likely due to a fault in the switch assembly. Blowing the circuit breaker is the harder issue. Since it only occurrs on the hand wash setting, it could be a faulty contact in the timer, or a shorted wire in the harness, but it would have to be a wire specific to the hand wash selection.

Was this helpful?

Latest Questions

i have replaced the atc switch and the water valve and i still can not get hot water to fill. I have volatage coming out of the atc switch to all the pins when I have it unpluged from the water valve conector but when I plug it into the water valves i lose volate to the hot water valve pins when it selecting hot water and I continue to have full 120 volts on the cold valve in any of the water temp. setting.

Travis for Model Number RTW440XQ0

Answer Hello Travis. You need to check and make sure the hot water works unhooked from the valve as well. If there is not power, and the switch and valve are new, it sounds like the wiring harness is bad and will need to be replaced.

Was this helpful?

Before I had no water to machine so I changed the atc. Now all I have is very hot water.

Rick for Model Number 11029522801

Answer Hello Rick. Based on the information you provided, it sounds like the water valve W10144820 is bad and will need to be replaced. If only the hot works and not the cold, and the temperature switch is new, the valve will need to be replaced.

Was this helpful?

the washer wont let water in on hot or cold i have hot and cold water pressure at both valves but when you set timer to wash nothing works

Rick for Model Number 11029522801

Answer Rick, Great job, You're on target, the ATC switch controls which valve to open based on the water temp. selected, When it fails, it will not activate the fill valve solenoids and the washer won't fill. Replacing the switch W10184148 should solve the issue. Thanks and Good Luck

Was this helpful?

Atc Switch Mid Level

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information