24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Electronic Control Board

Part Number: AP3890498
MFG Part Number: 8571903
Made by: Whirlpool
Our Price
$247.45
Regularly You Save
$294.47 $47.02

In Stock — Ships Today Guaranteed

Questions & Answers

22 Questions & Answers



Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Washer Control Board.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to determine if this part will work with your appliance.

Where can I find my model number?

More Product Images

Repair Help


Cross Reference Information

Part Number 8571903 (AP3890498) replaces 1180620, AH992556, EA992556, PS992556.

Have a Repair Question?
AppliancePartsPros has your Answer!

Questions & Answers

Read all 22 Questions

Ask a Question

Most Interesting

I have a front load washer I purchased. The front turn dial knob has had trauma and the blue piece that the turn dial knob pushes into is broke off inside the knob. Can I buy cycle switch or do I have to purchase an entire panel board?

Barbara for Model Number WFW8300SW03

Answer

Was this helpful?

My washer has codes f01 f24 it washes thru the cycles but will not fast spin at end of each wash cycle, at times I can do a drain and spin cycle and get it to work. I have unplugged this unit numerous times tying to reset everything, also checked the ccu board and motor control board for any burnt spots on the circuit boards, I see not hot spots anywhere. I do not have a test chart at the bottom of my unit it is missing. I know what the f01 says it is and what the 024 says it its, but that's a lot of money to spend if there is something minor wrong. At one time just checking on the internet I have read it is either the ccu or motor control board. I can get a new temp senor that not expensive

William for Model Number WFW8300SW000

Answer

Was this helpful?

Trying to find the right way to hook up control panel. Is there a video?

Darryl A for Model Number wsw8300sw01

Answer

Was this helpful?

Latest Questions

The washer runs until there is less than 5 minutes in the last spin cycle then it quits, the LCD screen goes blank and the door stays locked. The problem is intermittent, happens about 50% of the time. If I try and run another run right afterwards, then it almost always has the same problem again, or a Fault, I've seen two different faults, an F20 and an F27. The pump is not clogged, the hot and cold water supply are fine as I checked these. Do you think its the electronic control board (8571903) or the Microcomputer machine control (W10160252)? I've also seen mention in this forum about the line interference filter (W10367632), could it be that part? Thank you. Mark.

Mark for Model Number WFW8300SW04

Answer

Was this helpful?

The washer runs until there is less than 5 minutes in the last spin cycle then it quits, the LCD screen goes blank and the door stays locked. The problem is intermittent, happens about 50% of the time. If I try and run another run right afterwards, then it almost always has the same problem again, or a Fault, I've seen two different faults, an F20 and an F27. The pump is not clogged, the hot and cold water supply are fine I checked these. Do you think its the electronic control board (8571903) or the Microcomputer machine control (W10160252)? I've also seen mention in this forum about the line interference filter (W10367632), could it be that part? Thank you. Mark.

Mark for Model Number WFW8300SW04

Answer

Was this helpful?

The washer display is blinking on and off and the unit shuts down. If you can get it to start pumping water in it will quit that also and if it comes back on it will start the process over again. Could the problem be the control board. Thanks for the help

Chris for Model Number WFW8300SW02

Answer

Was this helpful?