Whirlpool W10166967 Oven Control Board

Total
$0.00

Part Number:	AP4358958
MFG Part Number:	W10166967
Made by:	Whirlpool

Our Price
$230.02
Regularly	You Save
~~$273.72~~	$43.70

Most Interesting

I have amaytag gemini electric double oven range. The control panel works. All elements, including the upper and lower ovens, and the surface burners, do not work. Nothing works except the control panel. I reset the circuit breaker, and not thing happens. Is the control board bad? Thanks.

Peter for Model Number maytag Mer6755aaq

Answer Peter, Since only the control panel is working you will want to check at your terminal block for 240 vac across the outside 2 posts. If there is not 240 vac then check from each of the outer post to the center post for 120 vac. Which ever side does not have 120 vac is the side you are losing voltage on. You will then want to check the power outlet for 240 vac. If there is power then you have a bad power cord and would need to be replaced. If you do not have 240 vac then you have a home wiring issue or the breaker is faulty.

Was this helpful?

For a while now we've noticed temperature differences in our lower oven. Now, it won't heat at all. I took the back panel off and tested the voltage output directly from the control panel. When I turn the lower oven on, I hear the relays "click" and I get a full 220V. Within 1-2 seconds, the relay "clicks" again and the voltage goes to zero. Is this just a bad relay(s) or the whole control panel? If it is a relay, how do I determine which relay is bad? Thanks

Robert E. for Model Number Maytag Gemini MER6751AAS

Answer Hello Robert, The characteristic of the relay clicking on and off is normal operation. This will occur with a new board in place. The test you performed proved you have a good board. Now you should test the lower bake element 7406P428-60 and the high limit 74009969.

Was this helpful?

Control board shows lock and there is no way to turn oven on or test the board ,it just beeps at you.

Mark for Model Number maytag mer6555aaq

Answer Mark, You will want to check your door latch to see if the latch switch is good. If the door is locked then you can try to disconnect power for 30 minutes and then back on to see if it will reset. If the door is not locked and there is no issue with switches on the latch, then the control would need to be replaced.

Was this helpful?

Latest Questions

The primary cooktop element of the 4 cooktop elements does not function properly. It cycles on and off, and generally will only heat up by running on high. Is there a controller / regulator for this heating element and how do you replace it?

Eric T for Model Number Maytag Mer6755

Answer Hello Eric, The element itself would have to be replaced as it is the limiter that has failed causing the element to continuously cycle. To replace you would open oven door and take out 1 screw on either side, Lift up on top and slide forward. Disconnect harness connector at the back and turn cooktop over. When replacing element pay attention to which numbers the clips are attached to so that when you put it back on they will be in the same position.

Was this helpful?

Everything on the stove works correctly except the cancel button on the control panel for the top oven will not shut off the top oven. I have to go and trip the breaker in the panel to shut off the oven. The button under the panel feeels "dead" to me. Do I need to replace the whole control panel and membrane or can the control be repaired. Thanks, AL

Al for Model Number MER6755AAB

Answer Hello Al, The membrane is not a repairable part and you would have to replace the control W10166967 on the unit.

Was this helpful?

Maytag Gemini double electric oven. Everything works except top oven bake. Control board is only sending 110v to one side. Other side reads 0v. Does the control board need to be replaced? Bake element is fine.

John J for Model Number mer6755aaa

Answer Hello John. When you tested the voltage did you go from wire to ground on each side? Also, if you tested between both wires you should be getting 240v. If everything else works fine as you stated then it could be a bad relay in the control board W10166967.

Was this helpful?

Oven Control Board

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information