Whirlpool 8300440 Control Panel Assy W/membrane, Switch (black)

Total
$0.00

Part Number:	AP3043893
MFG Part Number:	8300440
Made by:	Whirlpool

Our Price
$156.65
Regularly	You Save
~~$185.41~~	$28.76

Most Interesting

I have a Whirlpool Gold Double Convection oven. I have had to replace the microprocessor behind the touchpad control twice previously, a thermal fuse once and now most recently I have no ability to turn off the lower oven unless I flip the breaker once the lower oven's use is complete. I got the E1 F2 error this last week and just assumed that it was the microprocessor again. I got a rebuilt microprocessor from the same supplier as previous and upon getting everything installed I almost immediately got the same NO low oven off control and then as I was cycling through the remaining controls it went into E1 F2 error mode. I have tried pencil eraser cleaning of the ribbon contacts, business card on the non-contact side of the ribbon, trimming 1/16th off the ribbon to reset the contact patch on the strip. All of these attempts held the same effect as described above. Is this pointing toward the touchpad and ribbon having gone bad or should I be looking toward another problem. I don't believe it to be another issue since the screen is bright and clear but I may be missing something. Thanks for any input.

Warren for Model Number GBD307PDB09

Answer Hello Warren. It sounds like the touch pad is bad and will need to be replaced on the unit.

Was this helpful?

How do I take the control panel off to get to the circuit board Part # 8300440?

Duane for Model Number GBD307PDS7

Answer Hello Duane. You will remove the side trim off the oven, then remove the screws from the bottom corners of the control panel. Make sure the power is disconnected and lift off the control panel and access the board in the unit.

Was this helpful?

Display only beeps. I turned power off for about 1hr. When I turned power back on- heard 1 beep and sounded like it was resetting. When that stopped I hit upper oven to start- it seemed like it was trying- still no display. After, less than 1 min. it shut down- there was some heat inside. I tried to check the fuse and it read "0"

Don for Model Number GBD307PDS09

Answer Don, You'll need to check the resistance and voltages from the control transformer first 9760587. Since there's no display, but the control beeps, there's an issue with the low voltage side of the transformer, or you may have a faulty display circuit in the control board W10406070.

Was this helpful?

Latest Questions

Maytag range with F9 error code. Oven portion will not activate nor will the self clean work.

Answer Hello D.T., The F-9 Error is a door latch fault. You will need to order and replace the door latch assembly. I normally list the part number, but this is one of those parts that is model specific. You can either re-post with a model number or you can call [1-877-477-7278] and provide the model number to the customer service representative and they will look it up for you.

Was this helpful?

Our Whirlpool built-in electric double oven Model GBD307PDB09 has several problems I think are related to the control panel. The display panel when lit displays E6 and F2. In this state if I press the bake button, the oven will stay on for a random period of time, then cuts offs, beeps, then control panel fades to black. Other times we hear two beeps and we know the control panel has faded to black and the oven does not work at all (except oven light). What part do we need to fix the oven. Also is do instructions come with the part? Thanks, Pam

Pam for Model Number GBD307PDB09

Answer Hello Pam! The F2-E6 failure code indicates a shorted key pad, which on your model is included with the control panel. Your part number is 8300440. Please use this link to assist in your repair: http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/143511-led-display.html . Refer to section 4-2 in the PDF provided by the tech. Hope this information helps you, thanks!

Was this helpful?

The control panel doesn't show anything on it at all. You can open the door and the light comes on.. What part do I need to fix?

Jazhonker for Model Number GBD307PDS09

Answer Hello Jazhonker. Test and see if there is power coming to the control board. If so, you will need to replace the control board W10406070. Also, if there is power coming up to the board, make sure the control panel fuse 4451042 is good. If not it will cause the issues you are having as well. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Control Panel Assy W/membrane, Switch (black)

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information