24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Electronic Control Board

Part Number: AP4360738
MFG Part Number: W10189966
Made by: Whirlpool
Our Price
$208.98
Regularly You Save
$250.78 $41.80

In Stock — Ships Today Guaranteed

Questions & Answers

137 Questions & Answers



Description

Washer machine, motor control board and water pressure transducer.

Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Washer Control Board.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to find out if this part will work with your appliance.

Where can I find my model number?

Repair Help


Cross Reference Information

Part Number W10189966 (AP4360738) replaces W10155109, W10188476, W10130544, W10121508, W10201186, 1469076, 8576385, 8576386, AH2341877, EA2341877, PS2341877, W10051171, W10051176, W10104820, W10104830, W10112111, W10112112, W10112113, W10121311.

Have a Repair Question?
AppliancePartsPros has your Answer!

Repair Video

How to Replace Electronic Control Board #W10189966

Step by step instructions on how to replace a Electronic Control Board #W10189966 for Washer made by Whirlpool, Kenmore, Maytag. Note: This video is intended to give you the general idea of the part replacement procedure. Your appliance may differ depending on the manufacturer and model.


 

Comment on this video

Did you find this video helpful?

 

Questions & Answers

Read all 137 Questions

Ask a Question

Most Interesting

I have an Error code of "F1" on my washer. What would that code mean and what do you suggest checking so I can get the right part to replace? Thank you, Warren

Warren for Model Number WTW6400SW3

Answer

3 people found this answer helpful.

Was this helpful?

My cabrio washer drains for a long time just before the spin cycles, then never spins. It shuts off starts to beep and give me the code ld. So, if it stops at the rinse cycle I shut it down unplug for a few minutes then start back up on the rinse and spin cycle only and it works fine. I do the same thing when it stops on the drain and spin cycle. I just replaced the rods and springs for a shaking problem, fixed it right up. Now if I could figure out the spin cycle problem my washer would be perfect. Can you help, Thank you.

Henry for Model Number WTW6600SW0

Answer

1 person found this answer helpful.

Was this helpful?

I have a Whirpool Cabrio washer model WTW6600SW2 which as developed a serious problem with Out of Balance (UL). I tried leveling the unit, cleaned, greased and serviced the suspension system, removed the agitator and drum to clear any debris. I inspected the supports and sus[pension, and it all appears to function normally. No broken or misplaced parts, but is it possible for the springs to wear out? I tried small, perfectly balanced loads (4 towels evenly spaced, 4 shirts evenly spaced, 4 pants evenly spaced) and no matter what i do it repeatedly goes off balance and bangs loudly before stalling with the UL code. The only load the runs OK is a very small (light) load. Heavy loads cause frequest UL stalls, and i cannot even get a load done. Any ideas on how to resolve this?

Jim for Model Number WTW6600SW2

Answer

1 person found this answer helpful.

Was this helpful?

Latest Questions

I removed the agitator and found that the shaft spline groves were damaged on the hub inner engagement hub. I had a Sd code but It cleared when I pumped out the water again in the rinse cycle. The washer stops at 13 min on the spin cycle. Pump continues to pump but no spin. since the splines are shot I am thinking that must be the problem. Your thoughts?

Dan for Model Number WTW6400SW2

Answer

Was this helpful?

I get an LF (long fill) code during the rinse cycle for normal, casual and colors loads

Shawn for Model Number wtw6400sw2

Answer

Was this helpful?

I keep getting an Sd ( suds detected )error code. Believe me that there is no suds or soap at all in the unit after attempting to run unit 4 times empty and ran 2 clean machine cycles. It pumps out the water rather quickly and you can hear the pump run dry but the pump continues to run until the Sd error code sets. please help!

Robert for Model Number kenmore elite Qasis HE. 11027082601

Answer

Was this helpful?