Whirlpool W10207397 Element - AppliancePartsPros.com

Total
$0.00

Part Number:	AP4514837
MFG Part Number:	W10207397
Made by:	Whirlpool

Our Price
$44.33
Regularly	You Save
~~$52.31~~	$7.98

Most Interesting

Whirlpool Oven Unit: Boiler element working, baking does not. Pulled out bottom element and left hand wire burned off at connector. Unit tripped breaker. Is it a bad element or some other issue that caused short, and now what do I do about hte burned connector. Thanks for your help.

Rich for Model Number GMC275PDQ5

Answer Rich, You will want to check the resistance of the element to make sure that it is good. The resistance should be approximate 28.8 ohms. If it has proper resistance then the part is good. If not then replace the element. The connector can be replaced with a high voltage 1/4" female spade terminal.

Was this helpful?

I have a Whirlpool Double Oven (Model # RBD277PDQ1) wall unit. I ran the self-cleaning cycle and then cleaned out the oven. Since I did this, the upper oven looks like it is working according to the lights on the control panel, but it doesn't heat up at all. Neither element get's the slightest bit warm. Do you think it is a problem with the thermostat or the heating elements? By the way, the bottom oven still works fine. Thanks!

Michael R. for Model Number RBD277PDQ1

Answer Hello Michael. You will need to test the thermostat 4450934 on the unit and see if it reads closed. If not, you will need to order and replace the thermostat on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

My brother cleaned my oven and now nothing heats, both lower and broiler don't work. Sounds like its working but no heat.

Ray for Model Number rmc305pdq2

Answer Hello ray, You will want to check the thermostat to make sure that it has continuity. If not then the thermostat is bad. You can check the control with the oven turned on you should get 240 vac between bake and L1. If you are not getting voltage then the control is bad.

Was this helpful?

Latest Questions

Note: This question is for the older version of this part, but we thought you might still find it helpful

Whirlpool oven bake element not heating. Ran a continuity check of bake element and it is good, showing only about 23-30 ohms. Checked voltage on both sides of element, and they are both good 120+ volts on each. Broil element is heating normally as it would during preheat cycle. Is it safe to assume that even with good continuity there is a problem with the bake element since there is good power to each lead wire? Thanks

Jon W. for Model Number rbs305pdq14

Answer Hi. The element part # W10207397 ohm reading is correct. Make sure you have proper 240 vac at the terminal block. Make sure you have 120 vac from each outer terminal block stud (L-1 & L-2) -to the center (neutral). Ohm each terminal separately to its mount (ground). See if the element is grounded to its outer sheath. If so then you can be getting a partial "red" heating just to the area of where it is shorted and not heating correctly. Isolate the bake feed wire from the terminal block to see if you are getting the 120 vac or if the wire connection is bad. Isolate the bake feed wire from the clock relay to the element. Put the Red meter lead into the female spade of the bake relay wire you took off the bake element. Select bake and see if you have 120 vac on the bake wire and the clock relay output is good. You have to measure voltage with at least one element wire disconnected. This way you know each feed leg (L-1 & L-2) are good and you are not reading "back-voltage through the element. A common issue allowing one to think that they do have the correct voltage. Tricky if you will. Thank You.

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

Bumped foil against bake element and it started a little fire, which went out immediately, but now element won't heat well. (Takes 2 hours to get up to temp). I assume it shorted out the element??? This is an old, otherwise perfect shape, Whirlpool self cleaning oven,(1982), Model number RJE375ONO. Which element would be correct to buy? Thank you!

Grace for Model Number Whirlpool Model RJE375ONO

Answer Grace, the replacement bake element used on your model is part number 308180. Thanks!

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

I am looking for a Heating Element for a Old Hot Point Oven (Bottom) the Model# was given to me as follows. RB757GOT1AD does this even exist anymore.??

Jerry L. for Model Number RBD757GOT1AD

Answer Hello Jerry. WB44K5012 is the bake element for the model number you provided.

Was this helpful?

Element

Questions & Answers

Appliance Compatibility Tool

Repair Help

Repair Video

How to Replace Element #W10207397

Comment on this video

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information