Whirlpool W10176591 Flowmeter - AppliancePartsPros.com

Total
$0.00

Part Number:	AP4364631
MFG Part Number:	W10176591
Made by:	Whirlpool

Our Price
$15.51
Regularly	You Save
~~$18.46~~	$2.95

Most Interesting

Would want to know what to look for (1) were is the pressure switch (2) what to look for to test it should there be 110 voltage there? if not what would the ohms be? The machine will only spin will not let water in or agitate, there is no power to the water sol. To continue my question for got to say that this has a auto water level sensor have checked tubing to the water temp.setting. Where to from here? It says it has (Auto Loading sensing Triple Spray Technology)

Gary for Model Number wtw57esvw1

Answer Gary, The water temperature switch and the load sensor switch(water level switch) in your washer is W10248240. If you disconnect the air hose and blow into the hose, to clear any possible debris or clogs in the tube, and replace the switch, you should be fine. Power into the switch is on the purple wire from the timer and out on the blue/orange wire, there aren't any listed resistance or voltage checks for the switch, at this point.

Was this helpful?

Gary for Model Number wtw57esvw1

Answer Gary, The pressure switch is located in the control board behind where the water level selector knob is. You will want to check the pressure switch hose to make sure that it is not clogged or kinked. Check the air dome that the hose goes to and make sure that it is not clogged. To check the pressure switch you will do a continuity test in each level to make sure that you get continuity when pressure is applied. You can apply pressure through the hose by lightly blowing into the pressure hose.

Was this helpful?

How do you test the pressure switch on a whirlpool washer Mod. wtw57esvw1?

Gary

Answer Hello Gary. If the unit agitates, but does not fill, the temp switch is bad. As for testing the switch, You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Latest Questions

Would the flow meter have anything to do with the hammering of my pipes when the washer stops filling with rinse water. This only happens when rinse water stops entering machine? I just replaced the sensor switch about a month ago. Because it would start to agitate before the water entered the machine. This now works. Now i have this problem. It all has to do with this centennial maytag washer. It is the only appliance that does the hammering

WASHER2 for Model Number wvwc6esww0

Answer Washer2, Normally what causes the hammering sound would be low water pressure. You will want to pull the hoses off the water valve and check to make sure that the screens are not clogged. If clogged clean out and recheck. If still making noise then the water valve would be at fault.

Was this helpful?

Almost 3-year old washing machine stopped between wash and rinse cycle, and would not fill with water. Tried all different wash cycles, extra rinse cycle, etc. to try to get water to enter. None - no sounds, nothing. The spin cycles DO work. Note: Switch-Sen replaced when machine was 1.5 years old. What part(s) should I order to try to fix myself ? Am thinking water inlet valve? Another Switch-Sen? Or should I have it hauled away? Thank you.

Hope for Model Number Whirlpool WTW57ESVW1 washing machine

Answer Hello Hope, You will want to test to see if you are getting power to the water valve when the unit calls for water. If there is 120 vac then the valve may be bad. Check to make sure that the screen in the valve is not clogged. If this checks ok then replace the valve. Also check to make sure that the pressure hose is not clogged or kinked. Check to the lid switch for continuity with the door closed. If no continuity then you would need to replace the lid switch.

Was this helpful?

I have a top load whirlpool washer wtw57esvw0 that will not start now. I dont know if there is a water sensor switch or the flowmeter or if it is the main control knob that has gone bad. It will not initiate filling with water. It will drain and spin and will aggitate if started part way in the delicates cycle.

Boom for Model Number wtw57esvw0

Answer Hello Boom, You will want to check the pressure switch to make sure it is good. Also check the pressure hose for kinks and clogs.

Was this helpful?

Flowmeter

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information