Whirlpool 31001485 Gas Value (with Orifice)

Total
$0.00

Part Number:	AP4038318
MFG Part Number:	31001485
Made by:	Whirlpool

Our Price
$157.17
Regularly	You Save
~~$187.03~~	$29.86

Most Interesting

The ignitor starts, flame comes on, stays on for a min then goes out. ignitor starts again a minute later, the flame comes, high smell of gas. Clothes are not dried in an hour, but may be dried in 2 or 3. We did replace Dryer Igniters and Gas Valve Coils 3 years ago.

Chris for Model Number pyg2000aww maytag gas dryer

Answer Hello Chris. It sounds like the venting system is clogged or kinked. You will need to check the vent and clean it out. Be sure and clean the vent pipe and the dryer air duct assembly. If the air flow is not good, the unit will retain moist air causing the clothes not to dry. Try running the unit with the vent unhooked from the back of the dryer and see if the dryer works properly.

Was this helpful?

Dryer lights. Flame stays lite for about a minute then goes out. Ignitor goes back on but, flame does not restart. No smell of gas.

Garry L. for Model Number CyG2000AwW

Answer Hello Garry. You will need to test the thermostats and the flame sensor and make sure they are good. They should read closed for continuity. Also, check the igniter and make sure it is getting hot enough to light the gas. If all is good on the unit, you will need to replace the gas valve 31001485. Here is a link on how to use a multi-meter for the testing procedures. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

After using the dryer I can smell a little bit of gas coming out of the top of the valve. Should I replace the valve or try and repare it?

John T for Model Number pyg2300aww

Answer Hello John. It would be best to replace the valve 31001485 if it is leaking in the unit. Hope this helps.

Was this helpful?

Latest Questions

UNIT WILL NOT HEAT; HAVE REPLACED IGNITOR WHICH WAS BAD (HAD BURN MARKS AND CRACKED); HAVE REPLACED COILS AND STILL IGNITOR COMES ON BUT DOES NOT IGNITE GAS. (GAS IS COMING THRU) WHAT'S NEXT?

Novice for Model Number LNC8764A71

Answer Novice, What do you mean by "Gas is coming through" ? Before you replace the gas valve, remove and check the burner orifice for clogs or debris, and gas supply pressure to the gas valve assembly. Good Luck and Thanks.

Was this helpful?

Dryer starts and works fine. Open door to check clothes, close, push start and the dryer tumbles and the gas valve clicks on but does not lite, yet gas valve stays on filling dryer and vent hose with unburned natural gas. I think replacing the igniter may help lite the gas, but what safety feature is not turning off the gas in the event it does not lite?

Mike for Model Number Maytag

Answer Hello Mike! You would either have a short in the wiring harness or shorted ignitor 31001556. I would recommend you consider a new gas valve assembly 31001485 since the gas is not shutting off as it should. Thanks!

Was this helpful?

What should I be looking for when heat won't come on when drying on high like heavy cycle? It will work when on delicate cycle.

Guest

Answer Hi, are you sure the unit is heating on delicate cycle? If yes, then check the cycle switch part # 31001449. Make sure it is sending power to the ignitor on the cycle's you are experiencing issues with. If it's not sending power you will have to replace the switch, hope this helps!

Was this helpful?

Gas Value (with Orifice)

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information