Whirlpool W10190935 Ice Maker Control Module

Total
$0.00

Part Number:	AP4359694
MFG Part Number:	W10190935
Made by:	Whirlpool

Our Price
$92.06
Regularly	You Save
~~$110.57~~	$18.51

Most Interesting

Every so often when the ice maker goes to eject the ice into the bin, I would notice a piece would get stuck under the arm that pushes the ice out. I also have a problem with the fill tube freezing up for my ice maker, which is not a big deal I would just defrost it, but more importantly the ice maker stopped working. I am looking for some guidance as to troubleshooting the problem so I do not get the wrong parts. I have check out the I/R and i believe it is working right based on other threads I have read. What should i check next. Thanks William

William G for Model Number KSRA25ILSS01

Answer Hello William. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/refrigerator-freezer-repair/12038-whirlpool-ice-maker-does-not-make-ice.html

2 people found this answer helpful.

Was this helpful?

OK, I jumped out t&H control unit and the icemaker cycled, but did not fill with water. I switched wiring on the dual water valve and when I pushed the water dispensor I got water to the icemaker. Is the control motor bad?

William G for Model Number KSRA25ILSS01

Answer Hello William. It sounds like the control module is bad. If you switched the wires and the icemaker filled, then the module is bad. Hope this helps.

1 person found this answer helpful.

Was this helpful?

Ice control module screw for adjusting level. Do you turn clockwise for more and counter clockwise for less? Mine is over flowing do I adjust the screw that goes into the side of the module?

Frank M. for Model Number ap4359694

Answer Hello Frank! I have located a link on our free repair forum that will help adjust the water level. Hope it helps! http://forum.appliancepartspros.com/refrigerator-freezer-repair/173366-icemaker-overfills.html

1 person found this answer helpful.

Was this helpful?

Latest Questions

Sears Coldspot refrigerator: Noticed about a month ago that it was dispensing ice periodically only, instead of regularly. Then it stopped dispensing ice altogether. Then about two weeks ago, began dispensing ice again, albeit periodically. Now, has stopped dispensing ice completely again. It is getting water (I installed a heated water tube several years ago to stop the freezing of the water line) and there are ice cubes in the tray, but it won't dispense. I suspect the icemaker control module -- maybe -- or some electronic issue. I'm very handy at repairs but not so much at troubleshooting, so your help would be appreciated.

Efrain H for Model Number 106.55539400

Answer Efrain, It is possible that if the icemaker is not working that the issue could be the module, thermostat on the icemaker or the emitter board. When the icemaker is not working you can check to see if the light on the right side wall of the freezer compartment. If the light flashes then push in on the flapper on the left side and if it continues to flash then the emitter board is bad and if it glows solid then the emitter board shows good. You will then want to check the motor module for any burn marks. Check for the center wheel on the motor to make sure that the pins are not broken.

Was this helpful?

At first my icemaker would make ice, but it would not dispense it through the door. Now it has stopped making ice altogether.

Bill for Model Number 106.53552202

Answer Hello Bill. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/refrigerator-freezer-repair/29618-ice-maker-not-working-kitchenaid.html

Was this helpful?

Sir: The icemaker on my Whirlpool refridgerator was acting erratic the last couple of months.......it stopped making ice but when I would move the shutoff arm up and down a couple of times, the water valve would open and fill the ice trays. It would work as it should for a week then it would quit making ice again. I REPLACED the CONTROL MODULE (p/n W10190935) per video instructions. With the new control module installed, the water valve DOES NOT open to allow water to flow into the ice trays. I moved the shutoff arm up and down a couple of times to no avail. Can you help me with my problem? Thank you.

Peter

Answer Hello Peter. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Ice Maker Control Module

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Repair Video

How to Replace Ice Maker Control Module #W10190935

Comment on this video

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information