Whirlpool 9753108 Ignitor, Oven & Broiler Burners

Total
$0.00

Part Number:	AP3008600
MFG Part Number:	9753108
Made by:	Whirlpool

Our Price
$47.94
Regularly	You Save
~~$69.01~~	$21.07

Most Interesting

I understand how to test the valve with a multimeter but is there a a way to meter the igniter to see if it is the problem. Since there are two of them, it would make me feel better to know one of the igniters was bad or the valve was bad rather than know the valve is good but not which igniter to replace. Thanks for any help.

Barry for Model Number KGRT607HWH4

Answer Hello Barry. According to the manufacture the igniter 9753108 should read 85 to 95 ohms. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Gave you the wrong model number in my earlier email...should be KGRT607HWH4. Sorry about that. Question: Where does the wire harness plug in under the oven or on the back panel?

John D for Model Number KitchenAid Model # KGRT607HWH4

Answer Hello John. If you remove the igniter 9753108 from inside the oven, you usually can pull the connector out of the hole and replace the igniter on the unit.

Was this helpful?

When testing for the 3.2 to 3.6 VAC at the gas safety valve, do you measure voltage across the gas safety valve or across the gas safety valve and ignitor, or from the gas safety valve to ground? It appears the gas safety valve and ignitor are wired in series.

Rick for Model Number GW395LEGQ1

Answer Hello Rick. Across the gas valve with the igniter turned on.

Was this helpful?

Latest Questions

Oven is slow to ignite and you can smell gas occasionally. Does the igniter need to be replaced?

Rick for Model Number GW395LEGQ1

Answer Hello Rick. Test for 3.2-3.6 volts AC at the gas safety valve with the igniter turned on. If the voltage is there, you have a bad safety valve. If the voltage is low, you have a weak igniter and the igniter will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Oven is slow to heat, but broiler seems to be ok. Could it be the igniter for the oven broiler and oven work off the same gas valve?

Ed W. for Model Number kgrt607hbs4

Answer Hello Ed. Test the safety valve 9755424 with the igniter turned on and see if there is 3.0-3.4 VAC at the valve. If it is low, you will need to replace the igniter 9753108. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Oven very slow to heat up and flame on oven very small.

Ed W. for Model Number kgrt607hbs4

Answer Hi Ed. You will need to replace the oven gas valve part # 9755424.The igniter is part # 9753108.Thank you.

Was this helpful?

Ignitor, Oven & Broiler Burners

Questions & Answers

Appliance Compatibility Tool

Repair Help

Repair Video

How to Replace Ignitor, Oven & Broiler Burners #9753108

Comment on this video

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information