24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Motor Control Board

Part Number: AP3178728
MFG Part Number: 8541034
Made by: Whirlpool
Our Price
$227.62
Regularly You Save
$270.87 $43.25

Out of Stock — Usually ships within 5 - 6 days

Questions & Answers

15 Questions & Answers



Description

Electronic motor control board.

Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Washer Control Board.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to determine if this part will work with your appliance.

Where can I find my model number?

More Product Images

Repair Help


Cross Reference Information

Part Number 8541034 (AP3178728) replaces 661637, 661646, 8283266, 8317333, 8520857, 8520858, 8541034R, 949604, AH734021, EA734021, PS734021.

Have a Repair Question?
AppliancePartsPros has your Answer!

Questions & Answers

Read all 15 Questions

Ask a Question

Most Interesting

When I begin the wash cycle, it starts to fill and run but then after about 15 seconds it starts and stops randomly every few seconds. The time counter counts down very slowly or not at all. It is not displaying any error codes at all. I have run some of the "key dance" tests and it seems to be able to fill and drain OK and it runs through the nutation test OK but it will not complete the spin test. It will begin to spin for 3 or 4 seconds then stop very abruptly as though it is put into park. It will sit for a few seconds then begin to spin again with the same result. I have removed the front panel and I do not see any evidence of damage to the drive system that I can see under the tub. Thank you

Dave for Model Number 11022064102

Answer

Was this helpful?

My washer starts and runs about 5 seconds then code CE.

Sam for Model Number kenmore

Answer

Was this helpful?

I need to replace the part P/N 8541034 Rev.C on my washer but I only find a different Rev. The part number is the same but the Rev is D or A. Does it work if is different Rev. or it has to be the same Rev.?

Pepe for Model Number GVW9959KL2

Answer

Was this helpful?

Latest Questions

My basement had a slight flood, 3 inch of water. My washing machine now displays a f28 code mcu is not communincating with the ccu .. is my mcu damaged or need to be replaced.

Joe for Model Number kenmore h2 washer

Answer

Was this helpful?

Kenmore Calypso, was starting/stopping/starting/stopping during cycle, usually after many loads, usually at the end of a wash, but it varied. I ran the diagnostics three times successfully with no symptoms immediately after the symptom appeared. I never got any error code. The issue resolves temporarily if machine is let to sit for about 20 minutes and will finish the cycle. The issue does not appear until multiple loads have been run if the machine has not been used for a day or more, ordered and replaced the motor control board part and the issue persists. The pump seems fine when running in diagnostic mode or during washes before the symptom appears. It seems like it is an overheating board issue, but replacing the motor control board did not resolve the issue. Any ideas?

Mark for Model Number 8283430

Answer

Was this helpful?

Washer starts then display goes blank. After afew seconds starts again then stops etc. Eventually shuts down. Differt codes each time ce, ld, etc. Spins, nutates, fills, never makes it to drain. Control board smells burnt but no visual damage. Think I need control board, but may be motor control board. Replaced motor and u-joint kit and washer plate last year. Hope I can make it last a little longer. Thanks

Ronald B for Model Number 110.22084102

Answer

Was this helpful?