Whirlpool W10439651 Motor-Drv - AppliancePartsPros.com

Total
$0.00

Part Number:	AP5620185
MFG Part Number:	W10439651
Made by:	Whirlpool

Our Price
$141.09
Regularly	You Save
~~$169.31~~	$28.22

Most Interesting

Note: This question is for the older version of this part, but we thought you might still find it helpful

Appliance age is approx 20 years. Compactor does not fully compact the material in the drawer. The motor and ram function fine but the ram reverses before it has compacted.

Joe for Model Number Whirlpool TU8100XTP2

Answer Joe, You will want to check the directional switch at the top to make sure that it is adjusted properly. If this checks ok then the motor switch W10439651 would be faulty and need to be replaced.

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

I have a Kenmore compactor 66513605790. I can only get the compactor to compact by holding the start switch until I hear it go to the bottom then let go of the switch and it will stay down, after it's compacted I have to hold the switch until it rises all the way up again. Also the normal/extra pact switch blinks when it is compacting. Thank You for your help.

Dee for Model Number 66513605790

Answer Hello Dee, You will need to change the motor switch W10439651 to correct this issue.

Was this helpful?

I need to replace motor. The original motor (part # 776171) has been replaced by w10439651. Is this motor compatible with sdc800003 whirlpool trash compactor? I received the motor they sent me but my old motor doesnt have a brown wire to connect to the brown wire in the new motor. Thanks!

Dain I. for Model Number Whirlpool Trash compactor sdc800003

Answer Hello Dain! Yes, according to your model SDC800003 the drive motor W10439651 is the correct manufacturer replacement. The part part and may differ in appearance but is a functional equivalent to the original. Thanks.

Was this helpful?

Latest Questions

Note: This question is for the older version of this part, but we thought you might still find it helpful

My compactor works fine when in normal mode. When in solid mode, it will only run if you hold down the selector knob to the start position. If you let up on the selector knob, the unit immediately stops. If you hold it down long enough, it just cycles all the way down and then back up. If you let go of the selector knob half way through the cycle, the compactor stops at the bottom, where it should stop. How do I test the switches to determine which one I should replace? Kitchenaid Superba Trash Compactor

Brian G for Model Number kccc151jwh0

Answer Brian, We'll be sending you the information for testing the switches, as you requested. You're most likely on track, The issue is most likely in the motor centrifugal switch W10439651, based on your post description. Thanks

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

Unit has solid and normal buttons/switch. When set to normal, the unit cycles fine. When set to solid, I have to hold the start switch in the start position to get the motor to operate; however, the ram makes that knocking noise and doesn't go down. As a workaround, I have been setting to normal and waiting for the ram to go down just far enough before it starts to come back up. At that point, if I hit the solid button, the motor shuts off with the ram in the down position. When I am ready to open it again, I hit the normal button and the ram finishes the cycle. Does this sound like the motor switch or something else? Thanks!

Dave for Model Number KUCS02CRSS

Answer Hi Dave. Unit won’t keep running.• Top limit switch contacts open part # 777811. • “Solid or Dense Pack” cycle switch contacts open whether in “on” or “off” state (only on equipped models) part # 9872148. • Centrifugal switch contacts open (orange/black switch) part # W10439651. Use a volt/ohm meter part # TJMA-DM1 to assist you in your diagnostics. From what you described then I would focus on the Push button switch using the supplied wiring diagram stuck on the back of the unit. Thank You.

Was this helpful?

Note: This question is for the older version of this part, but we thought you might still find it helpful

The ram will not do down on my Kenmore trash compactor. Turn the knob to start and the motor runs fine, and the ram sounds like it tries to go down but doesn't move. I have checked the drive chain and tightened all bolts. I replaced the directional switch thinking that was it, but it made no difference.

Bob for Model Number 66513613101

Answer Bob,Remove the top and check for a broken or damaged power nut 9870163 or cap 9870775 on the ram assembly. Thanks

Was this helpful?

Motor-Drv

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information