24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Pcb Assembly

Part Number: AP4113560
MFG Part Number: 99002825
Made by: Whirlpool
Our Price
$193.48
Regularly You Save
$230.24 $36.76

In Stock — Ships Monday Guaranteed

Questions & Answers

20 Questions & Answers



Description

LED 12 button electronic control board

Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Dishwasher Control Board.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to find out if this part will work with your appliance.

Where can I find my model number?

More Product Images

Repair Help


Cross Reference Information

Part Number 99002825 (AP4113560) replaces 940548, 99002233, 99002260, 99002356, 99002366, 99002507, 99002825EXCR, 99002825R, AH2100156, EA2100156, PS2100156.

Have a Repair Question?
AppliancePartsPros has your Answer!

Questions & Answers

Read all 20 Questions

Ask a Question

Most Interesting

Maytag dishwasher, my dishwasher was in the middle of cycling, then my wife pressed the pause button to add more items, when she restarted it, the washer ran for 10 sec then stopped. The CLEAN LED light together with HEAT DRY LED started flashing, I tried to shut off the breaker a couple times but it did not reset. I think the circuit board is bad, but I want to know what you think is wrong with the washer. Thank you

Tuan V for Model Number MDB9100AWW

Answer

Was this helpful?

I just replaced the control panel on this dishwasher. I had to take out the PCB Assembly and put it into the new control panel. There is a green (I assume ground) wire that comes up from the wire harness to the PCB assembly I believe. I put it back where I believe it was on the PCB assembly but I want to make sure. There are two screws holding the right side of the PCB assembly to the control panel. I put the furthest right screw through the eyelet of the green wire and put that screw through the right hole on the PCB assembly. This hole is near what appear to be transistors. Is that the correct location? The screw and hole further to the left had no wires going to it if I recall correctly. Thank You, Tom

Tom for Model Number Maytag Dishwasher Model MDB9150AWB

Answer

Was this helpful?

My circuit board has stopped working. One of the large blue pieces (sorry I don't know what the technical term for that part is) has burn marks around the edges and has come loose. I'm fairly confident that replacing the motherboard will fix my dishwasher. If by chance this isn't the fix, what is your return policy. Thanks.

Robert C for Model Number MDB9150AWS

Answer

Was this helpful?

Latest Questions

I have had this MDB9100AWQ since 2001. There was a recall for the potential leakage around the control panel. The service was done in 2006 or 07. I think they replaced the control panel at that time since there was some corrosion. A couple of days ago I pulled the lower wash arm to clean out the water ports. When I tried to start the machine after the cleaning, the Control Panel was totally dead. I have since smelled burnt electronics around the door latch port on the door side directly above the control panel. I am assuming the control panel is toast. My question is: Was the cleaning of the washer arm and the likely death of the control panel a colossal coincidence? I am fairly handy and can replace the control panel but considering the age of the machine, I am concerned about spending a $200 and then have some other problem blow the new panel. Thanks for your help.

M.b.m. for Model Number Maytag MDB9100AWQ

Answer

Was this helpful?

The dishwasher would not run just click click. While contemplating the PCB and looking at it here, I saw Todds note about a bad solder joint. Ours too. Fixed that now it runs. BUT it seems to just keep cycling. Starts, runs, drains, dries, then starts a new cycle??? Thoughts?

Mark for Model Number Maytag MDB9100AWB

Answer

Was this helpful?

I bought the above dish washer in March 2003. I had to have the control board replaced in July, 2007. I now have a problem that the washer will not drain. It goes through the wash cycle but stops when it comes to the drain cycle. It just clicks and the readout panel flashes. This happens repeatedly. I had a technician looked at the unit and he said that it needed a new control board. My question is whether or not the part comes with any installation instructions. It seems like a rather simple job to remove the old panel and install the new one. The washer has sat unused since July 2011 when the technician looked at it. Thanks for your help.

Gene M. for Model Number MDB9150AWQ Part No. 999002825

Answer

Was this helpful?