24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Pulley, Spinner

Part Number: AP4027333
MFG Part Number: 22002315
Made by: Whirlpool
Our Price
$45.77
Regularly You Save
$54.47 $8.70

In Stock — Ships Friday Guaranteed

Questions & Answers

8 Questions & Answers



Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Washer Axle, Roller, Pulley and Washer Dryer Combo Axle, Roller, Pulley.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to find out if this part will work with your appliance.

Where can I find my model number?

Repair Help


Cross Reference Information

Part Number 22002315 (AP4027333) replaces 22001998, 824614, AH2020240, EA2020240, PS2020240.

Have a Repair Question?
AppliancePartsPros has your Answer!

Repair Video

How to Replace Pulley, Spinner #22002315

Step by step instructions on how to replace a Pulley, Spinner #22002315 for Washer, Washer Dryer Combo made by Maytag, Admiral, Crosley, Amana. Note: This video is intended to give you the general idea of the part replacement procedure. Your appliance may differ depending on the manufacturer and model.


 

Comment on this video

Did you find this video helpful?

 

Questions & Answers

Read all 8 Questions

Ask a Question

Most Interesting

How many bearings are on this washer and where are they located?

Frankie P. for Model Number nah6800aww

Answer

Was this helpful?

I replaced the bearings in my washer but there wasn't a snap in retainer clip included for the rear bearing so I finished the installation without it. How important is the clip? Am I gonna have problems without it? Every site I searched had that part discontinued.

Sam for Model Number Mah5500b

Answer

Was this helpful?

I have the same issue as Ed does above where the belt is actually cutting into the drum. I bought a new belt and it just runs off the pulley after I spin it 1 rotation. I noticed that the Pulley wheel is actually flexing from the tension on the belt and I have the tension as low as it can go. Is that part supposed to be able to flex at all or is mine just worn out?? Laundry is piling up! A solution would be greatly appreciated.

Sam P. for Model Number mah5500B

Answer

Was this helpful?

Latest Questions

Only in the spin cycle, the washer makes a loud roaring noise. When the spin cycle completes, the noise stops. I'm thinking it's the spin pulley. Would repalceing the pulley be the way to go?

Pierce for Model Number MAH4000AWQ

Answer

Was this helpful?

Everytime I tightened the bolt for the spinner pulley, the tub gets tight and it does not spin freely. I loosen the bolt and it is still tight. I took out the bolt and remoned the spinner pulley and turn the tub by hand and still tight. When I pound the shaft where the bolt screw in with a rubber mallet and spin it with my hand and it spins freely. When I put the spinner pulley back and tighten the bolt just enough so that the pulley doesn't have any play and tub gets tight again. Although I loosened up the bolt in order for it to spin freely again. By removing the pulley and pound on the shaft again then it moves freely. Is there something missing?

Dado A. for Model Number mah3000aww

Answer

Was this helpful?

Hello, I have the same problem described above, but my belt actually is cutting into the drum itself. In other words the belt is rubbing to the container and is cutting it. Also the belt is burned out due to the rubbing. Any suggestions, Thank you. Ed.

Ed for Model Number mah21pdaww

Answer

Was this helpful?