Whirlpool W10015830 Shock-Absr - AppliancePartsPros.com

Total
$0.00

Part Number:	AP4319288
MFG Part Number:	W10015830
Made by:	Whirlpool

Our Price
$33.45
Regularly	You Save
~~$41.81~~	$8.36

Most Interesting

Hello. My front load whirlpool washer recently started shaking violently during the spin cycle. Inspection of the shocks displays signs that they're bad, they all have grease accumulated at the end of the shock plunger. After reading some of the questions asked in the past I stumbled across a few that suggested the tub be checked, if it spins free but moves the tub might need replacing. Can you please explain what type of movement you are referring to. My wash tub spins freely. However, it does have a bit of movement towards the shocks, not much but it isn't completely stationary. How much rotational play should there be if any . Thanks, Alex.

Alex for Model Number Whirlpool duet front load washer

Answer Hello Alex. The inner basket is the part needing to the checked here. It should rotate fine, but nut have any movement upward, downward, or side to side. It should be snug in the bearing assembly. The outer tub assembly will move around and up and down and side to side. This is normal for it.

Was this helpful?

Is it hard to change the shock absorbers?

Stephane for Model Number wfw9150ww00

Answer Hello Stephane. The tub is held in position by four shock absorbers, two in front and two at the back. Each shock absorber W10015830 can be disconnected from the tub by turning the top of the shock mount counter clockwise, 90°. The shock can be removed from the washer by turning the bottom shock mount counterclockwise, 90°.

Was this helpful?

My washer shakes badly when a load is present. I have removed the botttom panel and seen some grease like substance on one of the shocks. Would this be a safe bet to replace the shocks? What exactly is meant if tub spins freely when turning the tub?

Eric for Model Number WFW9150WW01

Answer Hello Eric. The inner basket should turn freely and have no play in it. If it is loose, you will need to replace the outer tub assembly W10285625. If it is not loose, you will need to replace the shocks W10015830 on the unit, based on the information you provided. Hopoe this helps.

Was this helpful?

Latest Questions

I just got done replacing my bellows and I noticed the 3 shocks inside of my unit. It seems like an odd design to only have 3 especially when there are holes for 6 total 3 per side. On one side there is something blocking one of the shock holes but on the side with one shock there are 2 open holes was wondering if it would help to reduce vibration by adding at least 1 more shock so that there is 2 on each side?

Matt for Model Number MHWE200XW00

Answer Hi Matt. This unit is only designed for the 3- shock absorbers part # W10015830. If there is any visible grease leaking and if the shock compresses easily on it's own, then replacing them is a good effort weel spent. Thank You.

Was this helpful?

Does my model use three or four shock absorbers?

Dre for Model Number mhwe200xw00

Answer Hello Dre! Your unit uses three shock absorbers W10015830. Thanks!

Was this helpful?

I have a washer that works perfect except when is going into high speed spin cycle, It cluncks and shake very bad. Is this the shock or springs that need to be replaced on this machine?

Chuck for Model Number WFW9200SQA12

Answer Hello Chuck. You will need to turn the inner tub by hand and see if it feels loose. If so, you will need to replace the outer tub assembly 280232. If it is tight and the tub does not drag, you will need to remove the toe panel and back access panel and inspect the shocks W10015830. Hope this helps.

Was this helpful?

Shock-Absr

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information