Whirlpool W10189190 Start Device Combination

Total
$0.00

Part Number:	AP4369220
MFG Part Number:	W10189190
Made by:	Whirlpool

Our Price
$43.85
Regularly	You Save
~~$54.11~~	$10.26

Most Interesting

My Whirlpool fridge has an issue its seems to shut down to defrost and then doesnt start up. if I unplug the fridge and wait a while then plug it back in it usally starts back up and cools both sides great for a couple of days then repeats its self. Any ideas?

Wes A for Model Number GC3SHEXN502

Answer Wes, If the unit is not coming back out of the defrost cycle then the relay on the control board is sticking and the control board 2307037 would need to be replaced.

Was this helpful?

My refrigerator quite cooling. I can hear the compressor start and then kick out within seconds. Would the start device combination correct the problem or do you think the compressor is bad?

John for Model Number MSD2572VEW01

Answer Hello John, This sounds like the start relay/overload combination device W10189190 need to be replaced.

Was this helpful?

I bought the relay/overload start device combo and I have a question...There are only 2 visible places on this new start device to attach the wires that are coming from my fridge. Which ones do I use? From the fridge, I have 1 black (or dk blue)wire, and then another clip/connector with a combo of a white and 2 black (or dk blue)wires going to the old relay. The old relay plugged onto 2(bottom) of the 3 posts of the compressor. The top post of the compressor has a black wire connected that goes to the overload. There is also an orange wire going to a connector on the overload and a dk blue wire going to a separate connector on the overload. which ones go where?

Brenda for Model Number NNS228GA

Answer Hello Brenda, You will have to trace wires back to the condenser fan motor. The hot wire coming off the condenser fan motor, either blue or orange will go to the L1 on the new relay. The white wire from the condenser fan will go to the N on the new relay. The other wires will be eliminated from the circuit at this point.

Was this helpful?

Latest Questions

Need to know how to disconnect relay and overload kit(W10189190) from compressor to check for burn marks or rattling from what I have read, dont want to break it trying to take pieces off in wrong order. problem fridge runs but does not get cold on either side, can hear compressor kick on and a few seconds later turn off, no other apparent problems

Phucthefridge for Model Number GDSRVAXVY01

Answer Hello phucthefridge. You need to make sure the power is disconnected. You will pull the relay off the unit first. Then the overload pulls off the compressor. If there is a cover on there, you will need to remove the cover to access and remove the parts. Both parts in the start kit W10189190 pull off the compressor.

Was this helpful?

I am replacing my original relay and overload with the combo part AP4369220 on my refrigerator. The refrigerator has 5 wires that were connected to the old relay and overload. Can you tell me how do I need to connect those five wires to the 4 connectors on the new combo part. The wires I have on the refrigerator are 1 white, 2 black, 1 blue and 1 grey. Thank you.

Mike M. for Model Number SMD22TBW

Answer Hi Mike. Access your wiring diagram in the controls or the toe kick area. Blue / black combo. to the overload. Gray to the "S" terminal of the compressor from the capacitor. White from the capacitor and the other blk./ cond. fan motor goes to the "R " side of the compressor. Thank you.

Was this helpful?

Hello! I have the blue and black connected to the overload L as per the original connections and the circuit diagram. I have the other black connected to N and the capacitor is plugged into the bottom two slotted connectors. I forgot to mention in the email that the white and grey are not conencted. The white originally went to the other black that is connected to N and the grey went straight to the capacitor. I have checked the white and it appears that it is connect not to the capacitor but somewhere else. That is why I am asking if it should be connect to the black as it was originally. Be Well, Dave

Dave for Model Number SX25SW

Answer Hello Dave. Yes, the only wire you will not need is the grey wire. You will need to use the white wire with the black wire or it will not run. You have everything else wired correctly. Hope this helps.

Was this helpful?

Start Device Combination

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information