Whirlpool 22003302 Switch, Intertial Unbalance

Total
$0.00

Part Number:	AP4027729
MFG Part Number:	22003302
Made by:	Whirlpool

Our Price
$26.45
Regularly	You Save
~~$31.49~~	$5.04

Most Interesting

I have a may tag Neptune washer and it will not spinn unless I hold the door lock latch by hand and start the machine and when the lock light comes on close the door and restart. Could it be the latch or switch. The machine is around 13 years old.

Bruce

Answer Bruce, More than likely it will be the wax motor that is not pushing out enough to allow the latch to engage.

Was this helpful?

I have followed your instructions but still cannot locate the inertia balance switch can you be more specific about the location (do I need to remove any other panels to find it? The Maytag washing machine was purchased in 2003

Aussie J. for Model Number MAH300

Answer Hello Aussie. Find the switch on the bottom of the tub and trace the two blue wires going to the switch. This will lead you to the intertial unbalance switch 22003302. This is the easiest way to locate the switch on the unit.

Was this helpful?

Part AP4027729 & AP4026713 (Inertial unbalance swich). Do these parts come with directions as to how one can access the parts for replacement?

Roy for Model Number mhw2000aww

Answer Hi Roy. You need to go into the front of the washer by removing the door and hinge assy. Then remove the opposite door panel hinge holders. Then grasp the upper front panel inner /outer corners to slightly twist and pull out towards your waist. Then lift the front panel up and off the lower frame hinges, set the panel aside. The tub displacement switch part # 22002044 and the inertia balance switch part # 22003302 are mounted on the front rt. middle of the outer tub area. Thank You.

Was this helpful?

Latest Questions

My maytag neptune will not go into spin cycle. Could the problem be the unbalance switch?

Roy for Model Number mhw2000aww

Answer Hello Roy. Yes, if any of the unbalance switches 22003302 22002044 are bad you will need to replace the switch. They will prevent the machine from spinning. Also look for loose or broken wires going to the switches. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

My frontloader will not reach high speed spin and the message is it is out of balance. This happens with or without clothes and the machine is not vibrating very much. It does pump out water at full force but it sounds like water is still in it when I turn the drum by hand.

Dan for Model Number MAH7500AWW

Answer Hi Dan. There is a inertia unbalance switch part # 22003302. It is mounted on the outer tub on the rt. side. By pass these 2- wires to momentarily see if this is the cause. Check the foot pads to see if they are still intact and gripping the floor OK. Is the shocks leaking ? This will permit the unbalance issue. Is the unit level front to back and side to side ? Are the leg lock nuts tight up against the base assy. while they are level ? You can use the tech sheet supplied w/ the unit folded in a packet and put the unit in a diagnostic mode to assist. Ohm out the motor windings. Check the tach. circuit for proper ohms and connections being tight. Are the motor and motor control board connections tight ? Thank You.

Was this helpful?

What does this switch do? My machine keeps coming up with code 51.

Lorenzo for Model Number WTW6600SB2

Answer Hello Lorenzo. Based on the error code you provided, it sounds like you will need to replace the control board W10189966 and the speed sensor W10183157. Hope this helps.

Was this helpful?

Switch, Intertial Unbalance

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information