Whirlpool 22001638 Timer - AppliancePartsPros.com

Total
$0.00

Part Number:	AP4026344
MFG Part Number:	22001638
Made by:	Whirlpool

Our Price
$128.20
Regularly	You Save
~~$154.92~~	$26.72

Most Interesting

Machine stop working, there is power to the timer, the lid switch and , fill valves. No power from the timer to the motor we rotated the knob at different points and there was no reaction and no noise of any kind. sunny

Sunny for Model Number LAT8414AAE

Answer Hello Sunny, You will want to check the continuity of the lid switch. The lid switch could have power coming to it but if the power does not pass through then the unit will not start. Also if no water coming into unit then check the fill valve screens for clogs and check to make sure that the pressure switch is good and that the pressure hose and air dome are not clogged.

Was this helpful?

Hello, it appears that my timer needs to be replaced on my machine. It works in delicate but not the other cycles. The machine will fill with water on the other cycles, put it wont agitate or spin the water out. On delicate, works just fine. I found the timer I need, but most of the videos I have seen on how to take the knob off look a bit different than the model I have. How does the knob come off for this model? I will be ordering that part asap!

Nick for Model Number Maytag LAT9635AAE

Answer Hello Nick, To remove the knob on the timer yu will pry the cap in the middle of timer off and pull the retainer clip off the timer shaft. Then you remove the timer knob spring and dial.

Was this helpful?

I have a Maytag LAT8415AAE that works at different parts of different cycles. In "Regular" mode it will fill, but not agitate. Timer keeps advancing, then it spins and drains at last spin cycle. In "perm press" it filled, did nothing for first part, then spun and drained, then filled, and agitated during cool down rinse, then didn't spin and drain, moved to final rinse, no fill b/c it didn't drain, was already full of water, agitated then spun & drained until OFF. On "delicates"; filled and started to agitate, then stopped, didn't spin and drain, then agitated a little later, then spun and drained until off. I checked lid switch and water fill switch both OHM without washer plugged in then with voltage to ground. Also checked motor terminals. All seemed fine.

Mike

Answer Hi. The timer motor windings are shorted keeeping the advancing of the timer part # 22001638. Thank You.

Was this helpful?

Latest Questions

The lid switch checked ok.Still will not spin or agitate

Wynton O. for Model Number LAT8414AAE

Answer Hello Wynton. If the lid switch is good, and is working properly when the lid is closed, you will need to test for power coming to the motor assembly. If there is power there, and the motor does not run, you will need to replace the motor assembly on the unit.

Was this helpful?

Will not agitate, spin. Will fill but not empty.Failed with no prewarning. Any suggestions?

Wynton O. for Model Number LAT8414AAE

Answer Hello Wynton. You need to check and make sure the lid switch assembly 22001682 is not bad on the unit. If so, it will cause the issues you are having with the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

On normal wash cycle, won't agitate, will fill, and spin. Seems to function ok on perma press and delicate cycle. I think i need a new timer??

Sean for Model Number lat8415aae

Answer Hello Sean. Yes, it sounds like the timer is the problem with your unit. If it works on the other cycles, but not on normal, then the timer is bad. Hope this helps.

Was this helpful?

Timer

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information