24/7 Customer Support

:

Chat with a Pro


Part Number: AP4037259
MFG Part Number: 306176
Made by: Whirlpool
Our Price
Regularly You Save
$188.60 $30.11

In Stock — Ships Monday Guaranteed

Satisfaction Rating (1)

Questions & Answers

32 Questions & Answers


This gas valve includes the coils. For the coils alone use part number 279834

Genuine Whirlpool part. Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. See all items in Dryer Burner & Related and Washer Dryer Combo Burner & Related.
Whirlpool also makes various appliance models for Sears / Kenmore.

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to determine if this part will work with your appliance.

Where can I find my model number?

More Product Images

Repair Help

Cross Reference Information

Part Number 306176 (AP4037259) replaces 1689, 3-6176, 35001094, AH2029797, EA2029797, PS2029797.

Do-It-Yourself Stories from Customers like You
Total Satisfaction Rating
View All Do-It-Yourself Stories Have questions? Ask our pros!
Maytag gas dryer had no heat Martin R. • Brea, CA • October 03, 2014
Appliance: Maytag Dryer-Gas MDG6800AWW

My Repair & Advice

Was this review helpful to you?  

Most Helpful Stories

1 People found this story helpful
Do-It-Yourself Rating
  • 1
  • 2
  • 3
  • 4
  • 5
Easy Difficult
Repair Time Estimate

30-60 minutes 

Have a Repair Question?
AppliancePartsPros has your Answer!

Questions & Answers

Read all 32 Questions

Ask a Question

Most Interesting

I have a maytag MLG2000WAA, the igniter make the flame turns on at the begining, but after this when the igniter turns on I can hear like a intent to open the gas valve, but it is not posible. Turn off the dryer and after some minutes make the same cycle.

Gerardo for Model Number MLG2000WAA


Was this helpful?

I have MDG2500BWW gas dryer that is heating erratically. Ignitor cycles and glows, but often flame will not start. When this happens, there is a smell of natural gas out the vent. Have replaced ignitor and valve coils (all read proper resistances). In checking cables to coils, two prong coil cycles between 0.4V when ignitor glows, to 120V when ignitor turns off. So the coil should be energized when ignitor goes off. For three prong coil, read same voltage center ground to one outside prong, and read 118V to 120V to the other outside prong. Starting to suspect gas valve (utility work recently done on our street), maybe weak flow or valves not fully opening. Any way to check/clean? suggestions? Thanks.

Jim for Model Number MDG2500BWW


Was this helpful?

Air path clear. Continuity on hi-temp and flame sensor. With front panel off, igniter glows, gas flows and flame last about 10 seconds. Igniter then fades and flame goes out. Strong gas smell from unit afterward. Have replaced coils and igniter but same result. Is it possible that gas valve is not closing completely?? Suggestions?

Ron for Model Number MDG2500BWW


Was this helpful?

Latest Questions

How do you convert the Frigidaire FGX831CS1 to propane?

Patrice M. for Model Number FGX831CS1


Was this helpful?

I have a maytag dryer, the flame turns on for around 10 mins. then goes off and doesn't come back on until you shut the unit down and turn it back on. I've replaced: flame sensor, hi limit therm. , cycling therm., coils, ignitor and thermal fuse.

William for Model Number MGD9026AWW


Was this helpful?

My gas maytag dryer will not heat, the ignite lights and stays on for about 10 to 15 seconds, then i hear a click and it goes out tried replacing the coils with same result. I've tested flame sensor, cycling thermostat, high limit thermostat, and thermal fuse with all of them checking out good. Any idea's?

Nick for Model Number maytag mdg9316aww


Was this helpful?