Whirlpool 9755424 Valve & Regulator Assembly

Total
$0.00

Part Number:	AP3178816
MFG Part Number:	9755424
Made by:	Whirlpool

Our Price
$141.94
Regularly	You Save
~~$168.91~~	$26.97

Most Interesting

One burner cannot regulate the flame. It remains very low regardless how much you turn the knob. All other burners are fine.

Johnny for Model Number Dacor RGC365s/NG 36" cooktop

Answer Hello Johnny, You will need to replace the gas valve for that burner. Since you didn't mention which burner is experiencing the failure, the burner part numbers are as follows. You will need to order and replace the one for the burner giving you the issue. Single Valve, B-Burner-AP3727774 Single Valve, C-Burner-AP3773271 Dual Valve, D-Burner-AP3773250 Dual Valve, C-Burner-AP3773266

Was this helpful?

Hi , we have replaced the flex line and valve regulator assembly due to the gas company and a repairman, but there is still a gas smell coming from the oven when it is turned on any suggestions.

Jessie

Answer Hello Jessie, It sounds like the oven safety valve is not fully closing causing the gas smell.

Was this helpful?

I think I have a bad valve/regulator on my stove. Sometimes when I try to light the oven, I see the igniter glow, but smell gas and the oven doesn't light. We had a repairman out for something else and he said that the valve sometimes sticks and if I just tap on it when it is trying to light, it un-sticks the valve. He showed me which part to tap on and it looks just like the picture shown. When it comes to eventually replacing this part, is this something that the average do-it-yourselfer can do, or is this an official repairman install? I would really like to not blow myself up.

Kevin for Model Number KitchenAid KGRT607

Answer Hello Kevin. Test for 3.2-3.6 volts AC at the gas safety valve with the igniter turned on. If the voltage is there, you have a bad safety valve. If the voltage is low, you have a weak igniter and the igniter will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Latest Questions

Thank you for the reply. Can you please elaborate on the "flip the regulator"? I think the new regulator must have either the screwdriver slot or the "flippable" piece inside the regulator the sets the pressure on the diaphragm for either LP or NG? I only ask this because the factory regulator does not have a screwdriver slot for changing between the two fuel sources. I also assume that setting the orifice refers to the orifice that supplies gas to the oven, the piece with the air shutter on it. Thanks

Glenn B

Answer Hello Glenn. The brass nut under the plastic cap on the regulator unscrews and flips over for propane gas.

Was this helpful?

I will be replacing my gas valve (AP3178816) on my Kitchen-aid range due to it having a very slow leak. My range is currently set-up for propane, which I wish to continue using. Is there anything I have to adjust on the new regulator before using it? Thank you.

Glenn B

Answer Hello Glenn. Yes, you will need to flip the regulator and adjust the orifice on the gas valve assembly 9755424 until the correct flame is burning.

Was this helpful?

I have got a digital meter but it looks different than the one on the link you sent earlier. Is there a video you may have and that shows us how to use the meter for testing? Do I unplug the oven when testing? Thank you again!

ATL0510 for Model Number KGSC308LSSO

Answer Hello! Here is a link from our free repair forum, this should have information on how to use different multimeters. Thanks! http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Valve & Regulator Assembly

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information