Whirlpool 22003483 Washer Drive Belt - AppliancePartsPros.com

Total
$0.00

Part Number:	AP4029079
MFG Part Number:	22003483
Made by:	Whirlpool

Our Price
$37.89
Regularly	You Save
~~$45.09~~	$7.20

Most Interesting

My washer is not spinning my clothes dry enough. They are still to wet after spin cycle. I moved my washer away from wall and there is a lot of black powdery residue I assume is coming from the belt. Is this normal and could the belts need replaced and that is why the spin cycle is not affective?

Mary for Model Number Maytag Atlantis MAV6451AWW

Answer Mary, The residue would be partially from the belt. You will also want to check your pump to make sure that the bearings are good and that there is no clog in the pump.

Was this helpful?

Just before the spin cycle, the washer made a sound like it was going to begin the spin cycle, but the washer just went dead. Tried moving it to a different cycle but still nothing. After a few minutes the washer actually would turn on but still wouldn't go through any cycles. It will just hum like something is locked up. I was told it needed a new pump and belt. Does anyone know if this is actually what is needed.

Mawcmw for Model Number MAV7600AWW

Answer Hello Mawcmw, You can tilt unit back and take belt off. Once belt is off you can try to turn the pump pulley. If it will not turn then the pump would need to be replaced. If the belt is cracked or damaged then you would want to replace belt.

Was this helpful?

MAV9600EWW not draining/spinning at end of rinse cycle. If I reset machine to beginning of rinse cycle, it does drain & spin

Joan for Model Number TIGGER19707@YAHOO.COM

Answer Hello Joan, You will want to check the thrust bearing to make sure that it is lifting the brake for the unit to go into spin. By resetting it may have allowed unit to do this but the thrust bearing may be sticking.

Was this helpful?

Latest Questions

Washer makes horribly loud noise when spinning ........ sounds like it's ready to take off and go through the roof ---- repairman changed "Thrust B. Kit" and Belt ----- no change, washer still extremely noisy & repairman unable to find cause. PLEASE HELP !!!

Theresa for Model Number MAV6000AWW

Answer Theresa, If the repairman installed the thrust bearing and belt, and adjusted them properly, then the issue would be in the tub bearing assembly 12001598 or the gearcase bearing 35-6615. The bearing failure is usually preceded by a water leak from the washer, which washes the lubricant from the bearing and causes them to make noise.

Was this helpful?

During the spin cycle the washing machine makes a loud thumping noise like it is out of balance and travels across the floor. It also leaves an extreme amount of black soot all over the base of the machine and the floor.

Ewt for Model Number M7600AWW

Answer Hello Etw. You will need to look for plastic shavings in the bottom of the machine. If there are some, the snubber ring 21002026 will need to be replaced to balance the machine. Hope this helps.

Was this helpful?

Maytag model Number MAV6000AWW. Agitation is slow and the water will not drain during the spin cycle. If I reset the spin cycle, than it might spin properly. Also, I notice water behine the machine on the floor.

Rudy for Model Number MAV6000AWW

Answer Rudy, Does the washer make a grinding or chirping noise ? You may have a seizing bearing in the drain pump or a loose impeller. Also check and make sure the motor assembly "slides" free and easy on the base plate assembly, with the drive belt removed. The water on the floor, could be due to dripping faucets or hoses and a slow drain pipe. Good Luck and Thanks

Was this helpful?

Washer Drive Belt

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information