How to Find and Read Your Washing Machine’s Tech Sheet


AppliancePartsPros Team / Thursday October 29, 2026


A modern washer in a compact apartment laundry closet, warm light

The difference between guessing and knowing, on most washer repairs, is one folded sheet of paper. The tech sheet packed inside your machine lists the diagnostic mode, the error codes, and the test values for your exact model: the same data a service tech gets paid to look up. Here’s where it hides and how to read it.

If you’re troubleshooting any washer issue, whether it won’t drain, won’t spin, throws a cryptic error code, or does something bizarre mid-cycle, the tech sheet is where you start. It’s the single most useful document for DIY washer repair, and finding it takes about 30 seconds once you know where to look.

Full safety notes below

Safety First

Unplug the washing machine from the wall outlet before you go reaching inside the cabinet, behind panels, or anywhere near internal components. You may need to pull the machine away from the wall to access the power cord. The tech sheet itself is just a piece of paper or plastic envelope; grabbing it is low-risk, but building the habit of disconnecting power before opening up any part of a machine will protect you every time.

Tools and Materials

You won’t need much for this one:

  • Flathead screwdriver or putty knife (for popping the top panel on some top-loaders)

  • Phillips screwdriver (if accessing a rear panel)

  • Your phone camera (to photograph the tech sheet for easy reference later)

  • A gallon-size zip-lock bag (to protect the sheet when you put it back)

Step-by-Step: Finding Your Tech Sheet

Front-Load Washers

  1. Check inside the lower front access panel first. On most front-load washers from Whirlpool, Maytag, and Kenmore, the tech sheet is tucked behind the lower kick plate: that narrow panel at the very bottom of the machine. Pop it off by pressing the release clips or removing the screws at each end. Look for a folded sheet in a plastic sleeve, usually taped or clipped to the inside of the panel or to the base frame.

  2. Check the top of the machine next. On many Samsung and LG front-loaders, the tech sheet is taped to the underside of the top panel. Remove the screws at the rear of the top panel (usually two or three Phillips screws along the back edge), then slide the panel back about an inch and lift it off. The sheet is often in a plastic pouch stuck to the underside with adhesive.

  3. Look inside the door boot area or behind the detergent drawer housing on some European-style models. This is less common, but we’ve found it in both spots on certain Bosch and Electrolux units.

Top-Load Washers

  1. Lift the console (control panel) first. On most Whirlpool, Maytag, Amana, and Kenmore top-load washers, the tech sheet is folded up inside the control console at the top rear of the machine. Remove the screws at each end of the console’s back edge (usually two Phillips screws), then tilt the console forward or flip it up on its hinges. The sheet is typically inside a plastic bag, taped to the console housing or sitting loosely inside.

  2. Try under the main top panel. Some GE and Hotpoint top-loaders store the tech sheet taped to the inside of the cabinet, visible once you lift the main lid and look along the underside of the top frame. On certain models, you’ll need to release the spring clips at the front corners using a putty knife, slide it into the seam between the top and cabinet, about three inches from each corner, and push to release.

  3. Check the rear panel. A handful of older models store the tech sheet in a pouch attached to the rear access panel. Remove the screws, pull the panel off, and look for a plastic sleeve.

How to Read Your Tech Sheet

Once you’ve got the sheet unfolded, and some of these are large, printed on both sides with small text, here’s what you’re looking at and what matters most.

Error code tables. This is usually the first thing people need. The sheet lists every error code your specific model can throw, what the code means, and often which components to check. This is far more reliable than searching online, where you’ll find generic answers that may not match your model. If your washer is flashing F5 E2, for instance, the tech sheet tells you exactly what your control board is telling you.

Diagnostic test mode instructions. Most modern washers have a built-in diagnostic mode that lets you manually activate individual components: the drain pump, the door lock, the fill valves, the motor, one at a time. The tech sheet gives you the exact button sequence to enter this mode. On many Whirlpool-built washers, it’s a specific turn pattern on the cycle selector knob. On Samsung units, it’s usually a button combination held for several seconds. These sequences vary by model, which is why the tech sheet matters so much; there’s no universal code.

Wiring diagrams. These show every electrical connection in the machine. When you need to trace a wire, test a component with a multimeter, or figure out which connector goes where after disassembly, the wiring diagram is indispensable. Each wire is color-coded on the diagram to match the actual harness in the machine. If you’re troubleshooting a washer that won’t drain, for example, the diagram shows you exactly which pins on the control board feed the drain pump motor.

Component locations and resistance values. Many tech sheets include expected resistance (ohm) readings for motors, thermistors, heating elements, and sensors. This is gold when you’re testing parts with a multimeter; you don’t have to guess whether a reading is in range or not.

Common Mistakes to Avoid

Don’t throw it away thinking it’s packing material. We can’t tell you how many times someone has tossed the tech sheet during install, mistaking it for a random insert. If you still have your washer’s original packaging or installation paperwork, check there too.

Don’t skip photographing it. Tech sheets get damp, torn, and faded over the years sitting inside a washing machine. The moment you find it, photograph every section with your phone. Zoom in enough that the text is legible. Save those photos somewhere you can find them, a dedicated folder on your phone or in your email.

Don’t ignore the diagnostic mode. People read the error codes and skip right to replacing parts. Running the diagnostic test mode first can confirm or rule out a failed component in minutes, saving you money on parts you don’t actually need. When you’re ready to find the right part, grab your model number and head over to our repair help section to make sure you’re ordering exactly what fits your machine.

Don’t confuse the tech sheet with the owner’s manual. The owner’s manual is written for consumers and covers basic operation. The tech sheet is written for technicians; it contains the actual diagnostic and electrical data you need for repair.

Need More Help?

If you’ve found your tech sheet but aren’t sure how to interpret a wiring diagram or what a specific diagnostic code is pointing to, bring your question (and a photo of the relevant section) to our community at the AppliancePartsPros forum. Plenty of experienced techs and DIYers there who can walk you through it.

If you need any replacement parts for your appliances, you can enter your model number at AppliancePartsPros.com to locate and order them quickly. Most orders arrive in just two business days, and we have tons of great information in our repair help section and YouTube videos to help you troubleshoot.

Stay connected with the latest DIY tips, tutorial videos, and repair guides by following us on Facebook, Instagram, and Twitter. We love hearing about your repair stories and successes. If you need more help or want personalized guidance, feel free to contact or call us at 877-477-7278. We’re ready to help you take on your next project with confidence!

Since 1999, AppliancePartsPros.com has helped millions of people repair their broken appliances by providing high-quality original parts at well below retail prices, free support and troubleshooting, and award-winning customer service from an expert, friendly, customer support team!

⚡ Electrical safety — before you start
  • Disconnect power before you start — unplug it or switch off the breaker, and confirm it’s dead.
  • Follow your local electrical code.
  • Anything involving household wiring, outlets, or the breaker panel itself is licensed-electrician territory.

Written by: AppliancePartsPros Team

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *