TE Error Code on a Samsung Washer: A Troubleshooting Guide
Steven E / Tuesday August 29, 2023
Understanding the TE code error on a Samsung washer
The TE error code on a Samsung washer is a prevalent issue and its repair is crucial for maintaining the proper functioning of your appliance.
The error indicates a faulty temperature sensor, which can affect the water temperature during a wash cycle. This code can also appear as TE1 or TC depending on the model. Keep in mind that they are all the same error code.
Don’t let a simple error code interrupt your laundry routine – take control and get your washer back up and running smoothly!
READ MORE: How to Replace the Glass on a Front Load Washer Door
What causes the TE code error?
The TE code error is primarily a result of two key issues within the appliance: a possible malfunction with the temperature sensor – due to wear and tear over time or sudden damage – and the control board. The temperature sensor is responsible for monitoring the water temperature in your washing machine’s drum, and if it’s not functioning properly, it can trigger the TE error code on your washer display.
FIND MORE: Samsung washer parts
Importance of the water temperature sensor
The temperature sensor in Samsung washers serves the crucial function of continually monitoring the water’s heat levels during laundering and drying cycles for the best cleaning results.
Without an accurate reading from this component, your machine could run too hot or too cold, leading to poor washing results, damaged clothes, and even overheating.
A well-functioning temperature sensor is also vital to maintain energy efficiency in your washer. Your machine utilizes these readings to accurately regulate power usage during different stages of the wash cycle. If you experience a TE code error on your Samsung washer due to malfunctions with the sensor, it can affect performance and also lead to higher utility charges over time by drawing more power than necessary.
READ MORE: Tips For Preventing Laundry Damage in Your Washing Machine
How to troubleshoot the TE code error
Reset the control board
Initiating a hard reset of your Samsung washer’s control board can often solve the TE code error. This process involves the following steps:
- Safely disconnect the washing machine from the power source.
- Wait for about 10 to 15 minutes to allow any residual power to dissipate.
- Reconnect the washer to the power source.
- Power up your Samsung washing machine and see if the TE error code is now clear.
Checking the thermistor wiring
One of the most important steps in the TE error code troubleshooting process is to check the wiring on the thermistor on your Samsung washer. The thermistor is a sensor that helps regulate the water temperature during washing cycles.
How you can make sure the thermistor wiring is intact:
- Unplug the washer from its power source.
- Locate the back panel of the washer and remove it for easy access.
- Find the thermistor, which is usually located near the heating element.
- Inspect the wiring connected to the thermistor for any signs of damage or disconnection.
- Ensure all wires are securely plugged into their corresponding connectors.
- If you find any loose or broken wires, carefully reconnect or replace them as necessary.
- Use a multimeter to measure the resistance across the thermistor’s terminals to determine if it is functioning properly.
Inspect and replace the thermistor if necessary
Inspecting and replacing the thermistor is an important step in resolving the TE Code error on a Samsung washer. Here are the steps to follow:
- Unplug the washer: Before conducting any inspections or repairs, make sure to unplug the washer from the power source to stay safe.
- Locate the thermistor: The thermistor is typically located at the back of the washer, behind the access panel. Refer to your user manual or manufacturer’s documentation for precise instructions on locating it.
- Disconnect the wiring: Once you have located the thermistor, gently disconnect its wiring by unplugging the connector that attaches it to the control board.
- Inspect for damage: Carefully examine both ends of the thermistor and its wiring for any signs of damage or loose connections. Make sure there are no broken wires, bent pins, or corrosion on the connectors.
- Measure resistance: Use a multimeter set to measure resistance (ohms) and test the resistance across both terminals of the thermistor. At temperatures 68- 86°F, the thermistor should measure approximately 66.1k-36.9k ohms. Compare your readings with those specified in your user manual or refer to manufacturer guidelines to determine if they fall within an acceptable range.
- Replace if necessary: If you find that your readings are outside of the specified range or suspect that the thermistor is faulty, it may need to be replaced. Consult your user manual for guidance on obtaining the proper one or click here and find the part specific to your model.
- Secure connections: Once you have replaced the thermistor, ensure that all connections are securely plugged in and fastened according to manufacturer guidelines.
- Test functionality: Plug in your washer and run a test cycle to check if the TE error code has been resolved.
READ MORE: How To Use A Multimeter To Check Appliance Parts
Verify the water temperature settings
- Check the Auto Temperature feature: Make sure the Auto Temperature feature is set correctly according to your laundry needs. This feature automatically adjusts the water temperature based on the selected cycle.
- Run the diagnostic test mode: Some Samsung washers have a diagnostic test mode that allows you to check various functions, including water temperature. Consult your user manual for instructions on how to enter the diagnostic mode for your specific model.
- Manually measure water temperature: Fill a bucket with hot water and measure its temperature using a thermometer. Compare this reading with the temperature displayed on your washer’s control panel during a wash cycle.
- Verify correct hot water supply: Check that the hot water supply hose is properly connected to both the washer and the faucet. Make sure there are no kinks or blockages that may affect proper water flow.
- Confirm voltage supply: Make sure your washer is receiving an adequate voltage supply from your electrical outlet. Low voltage can result in incorrect water temperature readings.
READ MORE: How to Decide What Water Temperature to Use for Laundry
More information
By following the above steps and understanding the importance of the temperature sensor, you can easily diagnose and resolve the TE error code showing on a Samsung washer. We hope you found what you were looking for in this comprehensive guide.
For further troubleshooting guides, make sure to check out our blog and YouTube videos. You can also follow us on Facebook and Twitter!
With nearly a decade of experience in providing top-notch customer service regarding appliance parts and repair, Steven enjoys sharing practical advice, troubleshooting tips, and interesting information to help readers stay informed.