Parts for Ge PTS25LHSARWW: 02 - Fresh Food Door Parts

The GE refrigerator water filter is an OEM replacement part responsible for ensuring the quality of the water dispensed on GE Profile top and bottom freezer refrigerators. It is responsible for purifying the water before it reaches your glass or ice maker, providing you with clean and safe drinking water directly from your refrigerator. To maintain optimal water quality and ensure the filter's effectiveness, it is recommended to replace the filter every 6 months or when the rated capacity of 750 gallons is reached.

Over time, the water filter can become clogged with sediment, reducing its effectiveness. Regular use and the accumulation of minerals and contaminants can lead to the need for replacement.

Symptoms of a bad water filter include:

• Reduced water flow from the dispenser
• Ice cubes with an unusual taste or odor
• The filter indicator light staying on
• Visible particles in the water or ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. For the best performance, it is recommended to replace the water filter every six months or as indicated by the filter change light on your refrigerator.

A replacement white door gasket that seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. Fits compatible GE refrigerators that use part number WR24X10088. What it does:

• Replaces a worn or torn door gasket to restore a tight seal around the door
• Helps prevent warm air infiltration that can cause frost build-up and higher energy use
• Can reduce moisture and food spoilage caused by poor door sealing
• Useful when the existing gasket is cracked, split, flattened, or no longer seals evenly

• Inspect mounting channel and door surface for debris before installing; clean with mild detergent and water and dry fully
• Gasket typically presses into a retainer channel; align corners and seat evenly to avoid gaps
• Allow time for the gasket to relax into place; gentle warming can help fit—do not use open flame or excessive heat

This thimble door top is the white trim piece that covers and protects the upper edge of the appliance thimble/dryer vent opening, restoring a finished look and helping keep the seal area intact. What it does:

• Replaces a cracked, chipped or warped top trim to improve appearance and fit
• Helps keep the vent/thimble opening properly covered and aligned
• Protects the upper edge of the opening from wear and impacts
• Prevents gaps that can allow lint or debris accumulation around the opening

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; hold parts securely to avoid scratching surrounding surfaces
• Inspect mating surfaces and remove lint/debris before installing for proper fit

A replacement bottom door cap that restores the finished edge and support at the lower corner of the appliance door. Keeps the door looking complete and helps protect the hinge area from damage. What it does

• Covers and protects the bottom edge of the door for a finished appearance
• Helps shield the hinge/mount area from wear and debris
• Replaces cracked, broken, or missing bottom cap pieces
• Improves door fit and prevents snagging from a damaged trim piece

• One bottom door cap (white)

• Unplug the appliance or shut off power before starting work
• Remove any screws or retainers holding the old cap and snap the new cap into place
• Handle trim pieces gently to avoid breaking adjacent clips or tabs

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly