Kenmore Dishwasher 587.17259202 (58717259202, 587 17259202) Parts

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

Used on the upper rack track

Black

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

Replacement air diffuser that directs cold air from the refrigerator damper into the fresh-food compartment to improve airflow and temperature consistency. Ideal when the original diffuser is cracked, broken, or missing. What it does

• Directs and disperses cold air from the damper to help even out temperatures across shelves.
• Replaces a damaged diffuser that can cause uneven cooling or restricted airflow.
• May reduce vent rattling or noise caused by loose, cracked, or broken diffuser pieces.

• Disconnect power to the appliance before any service to avoid electrical hazard.
• You may need to remove shelves or drawers for access; keep small parts organized.
• Part typically secures with clips or screws—use basic hand tools and avoid forcing tabs.

This replacement latch mounting screw secures the refrigerator door latch assembly so the door closes and seals properly. Installing a fresh mounting screw restores a solid latch connection and reduces door movement or rattling. What it does:

• Fastens the door latch assembly to the cabinet or door frame
• Keeps the latch aligned so the door closes and seals correctly
• Prevents loose or wobbly latch hardware and related rattling noises
• Helps address symptoms like a door that won't stay latched or minor door play

• Turn off power to the appliance or unplug before working near electrical components
• Use the correct screwdriver and thread the screw straight to avoid stripping
• Do not overtighten — snug is sufficient to hold the latch without deforming parts
• Test the door operation after installation

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This is a replacement screw used to secure appliance panels and components, restoring proper fit and stopping looseness or rattling. It's a direct-fit fastener that helps maintain safe, stable operation when original hardware is missing or worn. What it does

• Secures panels, brackets, trim pieces or internal components in place
• Stops rattling or vibration caused by loose fasteners
• Helps maintain proper alignment of parts for reliable operation
• Restores missing or damaged mounting hardware

• Screw

• Disconnect power (and water if applicable) before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or parts
• Keep removed hardware organized before final assembly

No.7 plastic .375

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fit and helps prevent rattling or loose parts for safe, reliable operation. What it does:

• Fastens panels, trim pieces, or internal components to maintain proper alignment
• Secures parts that can vibrate or become loose during normal use
• Helps stop rattling, squeaks, or gaps caused by missing or damaged fasteners
• Suitable wherever the OEM specifies part 154041001 as the required screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screw hole and match thread engagement; do not force or cross-thread
• Tighten firmly but avoid over-torquing to prevent stripped threads or cracked panels
• If multiple or different screws were removed, keep track of each location for correct reassembly

This sump retainer secures the appliance sump assembly and helps keep the pump seal and surrounding components properly positioned to reduce leaks and maintain correct water flow. It's a small replacement part used during sump or pump repairs. What it does:

• Holds the sump housing or pump assembly in place to maintain a reliable seal
• Helps prevent water leaks from the pump/sump area when installed correctly
• Keeps internal components aligned for proper water circulation and drainage
• Commonly replaced when sump hardware is cracked, warped, or no longer secures the pump

• One sump retainer

• Power off and unplug the appliance before starting any repair
• Verify you have full access to the sump/pump area; removal of panels or racks may be required
• Inspect surrounding seals and gaskets; replace if damaged to ensure a watertight fit

This inner door assembly replaces the damaged or cracked inner panel on your refrigerator/freezer door to restore a clean interior surface and proper component mounting. It's the factory-style inner panel used behind the outer door skin. What it does:

• Forms the interior surface of the door and provides mounting points for bins, shelves, and hardware
• Restores a smooth, sanitary interior when the original panel is cracked, warped, or separated
• Helps keep door components aligned to prevent rattling or improper sealing
• Compatible with OEM door hardware and trim when original mounting points are intact

• Installation requires removing the door and outer door trim; handle screws and wiring may need to be disconnected
• Inspect and transfer any clips, gaskets, bins, or fasteners from the old panel
• Use proper support to avoid dropping the door; get a helper for safe handling of heavy doors
• Disconnect power and follow manufacturer safety instructions before servicing

Door spring that restores proper tension for the appliance door, helping it open and close smoothly and hold position. Fits as a direct replacement for worn or broken springs to improve door operation and reduce slamming. What it does:

• Provides tension to the door so it opens and closes with controlled motion
• Helps the door stay in the desired position instead of falling open or slamming shut
• Commonly replaced when the door feels loose, drops suddenly, or doesn't latch properly
• Simple replacement can restore normal door function without replacing larger assemblies

• Disconnect power to the appliance before beginning work and follow basic electrical safety
• Springs are under tension—support the door and use appropriate tools and eye/hand protection

This lower impeller directs wash water from the dishwasher's lower pump to the spray arms, helping restore proper water flow for better cleaning performance. Designed as a direct replacement for the lower wash impeller. What it does:

• Channels water from the lower pump to the spray system to maintain cleaning coverage.
• Worn, cracked, or clogged impellers can cause weak spray, poor cleaning, or unbalanced wash cycles.
• Replacing a damaged impeller can reduce unusual pump noise and help restore normal pump operation.
• Works with the lower pump assembly to maintain correct water circulation during the wash cycle.

• Disconnect power and water supply before servicing the dishwasher.
• Access the lower pump area by removing the dishwasher tub access or lower base as required by your model.
• Inspect the pump housing and seals for damage and replace any worn components to prevent leaks.

This upper impeller directs water flow inside the pump housing to restore proper circulation and help your appliance clean and drain effectively. It's a direct-fit replacement designed to match the OEM shape and flow path. What it does:

• Moves water through the pump to support normal wash and drain cycles
• Helps maintain proper spray pressure and cleaning performance
• Can reduce noisy or irregular pump operation when damaged
• Commonly replaced when cracked, chipped, or worn

• Disconnect power (and water if applicable) before starting any repair.
• Remove the pump housing carefully to access the impeller; keep track of fasteners and seals.
• Inspect the pump housing, shaft, and seals for wear; replace damaged seals or gaskets.
• Reassemble securely and test the appliance through a short cycle to ensure proper flow and no leaks.