Joe March 01, 2020 for Model Number Th41358584 Dish washer won't fill with water to proper level except for the pre wash cycle, the wash an rinse cycles are not getting enough water. Replaced the water fill solenoid valve still the same results. Your advise would be appreciated.
1 Answer Joe, unfortunately, the model number provided is not matching within our available database. If the model and serial numbers could be verified and provided in a new inquiry, this will allow for the most accurate information to be presented. Read More...
Kirk September 28, 2019 for Model Number FFBD2406NW11B My dishwasher is not completing a cycle and is running forever. What is the cause?
1 Answer Kirk, as this model only uses a thermistor to sense the water temperature, the most likely cause of this issue would be the main control 5304512731 getting stuck in a cycle. Read More...
Jay August 21, 2019 for Model Number FFBD2406NB9B The control panel on my Frigidaire dishwasher lights up, but the dishwasher doesn't start. 1) Is it likely just the control board? Or could it be the switch panel? Or both? 2) Is soldering required to replace either of these parts - or do they just plug in to each other? Thank you, JW
1 Answer Jay, If your control panel has lights then the main control is supplying the voltage and you must have a short in the console. 5304506719 would be your replacement. Read More...
Manaf June 17, 2019 for Model Number FFBD2406NW9B Dishwasher has starting issues. The start keeps blinking, and also stops/stuck once in a while with a blink. Manually starting seems to work but not always. The cleaning, heating all seems to be OK. Some issue with the control board looks it. Is this correct?
1 Answer Hello Manaf, the problem you are having with starting the dishwasher is likely a control panel problem, the repair part is 5304506719 switch assembly.. Read More...
James January 23, 2019 for Model Number LFBD2409LF3C Replaced Board #5304502611. Did not change anything. Blinking lights on panel. Will not work. What next? Can it be returned? I followed your instructions on replacement.
1 Answer James, Press and hold the cancel button and hi temp for about four seconds. Advance thru the test by pressing the start button until it will not advance or goes blank and try to start a cycle. Read More...
Jason December 31, 2018 for Model Number FFBD2406NS9B The dishwasher won't drain when on the heavy duty setting. It drains fine on normal setting and the tub will drain when you cancel the cycle. Do you think the control board is faulty?
1 Answer Jason, Since the unit drains fine in all other cycles the control would need replaced. 5304512731 Read More...
Ponch November 30, 2018 for Model Number FPID2495QFOA MY dishwasher keeps running, no water comes out but I hear motor running. I try to hit clear buttons but nothing. no matter what buttons I hit, nothing makes a difference. I cannot use my dishwasher for fear of burning it up? Help!
1 Answer Ponch, For this issue the most likely cause would be a control board that is faulty. Read More...
Dore G November 07, 2018 for Model Number FTFB2940FE1 Good Morning All Wise One, My washer will not start error code {LOC} comes up and any button push it just beeps.I changed out door lock But still have message on screen. Need Help Please.
1 Answer Dore, Try to push the options and select button at the same time for 3 seconds and see if the LOC comes off. If this does not correct the issue then this would most likely be a faulty control board. Read More...
1 Answer Hello Dave, I'm sorry but we will need to know at what point in the cycle the unit is stopping to give you an idea of what component could be the cause of the issue. Thank you for your patience and understanding in this matter. Read More...
Ben October 08, 2018 for Model Number FFBD2409LW0B I push the buttons to select the wash cycle that I want and the lights light up. When I push the start button, the lights blink and then go out. The dishwasher never starts. I don't know if it is the Control Board or the Switch Assembly that need changed. The door lock works fine. Is the problem the Control Board or the Switch Assembly?
1 Answer Ben, Based on this issue the most likely cause will be the control board since the unit shuts off when pushing any selection. Read More...