Sy June 02, 2025 for Model Number FGID2466QF6A We had a bad storm come through the other night and I believe my house was struck by lightning. The dishwasher display shows "8" only. Everything will light up like normal if the door is closed and opened but it will not function if any buttons are pressed. I killed power at the breaker and left it off for about an hour and re-energized with same results. What advice can you give me on diagnosing/fixing it?
1 Answer Hello Sy, thank you for contacting AppliancePartsPros.com Between the display showing 8, the unresponsive buttons, and everything lighting up but the unit not starting, this sounds as though the main control board 5304514670 has failed. If it were the keypad or door switch you should be getting an Er for the keypad or CLOSE DOOR scrolling across the screen for the door switch. Read More...
Auggie April 24, 2025 for Model Number FGHD2433KF1 Dishwasher would not drain. Changed pump problem solved but on short wash after 5 minutes . it changed to 99+.changed turbidity sensor.Changed main control board but now it shows 34s but won't anything.Whats up.
1 Answer Hello Auggie, thank you for contacting AppliancePartsPros.com This sounds like a door latch 5304525218 or main control 5304514670 issue. The door latch can be tested to make sure that circuit has proper continuity when the door is closed. Read More...
Gus April 24, 2025 for Model Number FGHD2433KF1 dishwasher would not drain. Changed pump and that worked but another problem popped up.On short wash after 5 minutes it changed to 99+.Changed turbidity sensor but now when i start it on short wash it reads 34s but nothing happens. Whats up.
1 Answer Hello Gus, thank you for contacting AppliancePartsPros.com This sounds like a door latch 5304525218 or main control 5304514670 issue. The door latch can be tested to make sure that circuit has proper continuity when the door is closed. Read More...
Nick February 18, 2025 for Model Number FGHD2433KF0 I can't select all of the modes on my dishwasher, and now when a cycle ends, the LED screen in the front goes blank (used to say 'Clean' at the end up until a week ago). I replaced the board with part #5304514670, but now it's even worse. Every mode shows '99+S' or something similar, and everything lights up when you open the door. If I try and wash on Normal mode, it will change it to another mode. My old board was yellow, and this one is blue with a number of differences. Is there anything else I can look at here?
1 Answer Nick, Based on the model number provided the 5304514670 is the correct main board for your machine. You may have a loose connection or even a broken wire in the harness. Read More...
Lorrie January 15, 2024 for Model Number Frigidaire A00411052 I can select wash features but start button doesn’t work.
1 Answer Lorrie, We will need to have the model number of your washer to be able to assist with your question. Please resubmit your question with the model. Read More...
Jack December 13, 2023 for Model Number FGID2466QF3A Dishwasher wouldnt turn on so I flipped the breaker off then back on and it showed a "PF" error code. Im assuming its a control panel issue but not 100%. What do you think?
1 Answer Jack, if the control lock is not activated and none of the buttons are responsive, the failure would most likely be in the main control 5304514670 based on the information provided. Read More...
Sher August 21, 2023 for Model Number FGIP2468UD I have an error UO. I read it may be the vent on top of the dishwasher. Now I have no lights on the led panel..I moved the dishwasher and The UO error came back momentarily but now it blank again
1 Answer Hello Sher, check the wire harness going to and from the control board for any wiring problems. Read More...
Surya August 15, 2023 for Model Number FGID2466QF9A The dishwasher halted its operation during the middle of a cycle and presented an "Er" error message. After resetting the circuit breaker by turning it off and then on again, the display briefly indicated "195" for approximately 30 seconds before returning to the "Er" message. I'm unsure which component might require replacement to resolve this problem. Could you offer any insights or recommendations for addressing this issue?
1 Answer Surya, the error Er is going to indicate that the keypad has shorted out. This would require that the console 5304520552 be replaced. to correct the failure in accordance with the manufacturer's information. Read More...
Millie Rahrer May 20, 2023 Im trying to order a part for my frigidaire dishasher and I erroneously hit a wrong button to cancel - I want to cancel ebay and start over,
1 Answer Millie, The company you have contacted is Appliancepartspros.com and we would not have any information on EBay orders. Read More...
Yvonne April 03, 2023 for Model Number FGCD2456QFOA I need to replace my door control panel. I can't read the function panel plus the buttons are broken. Where can I find this part or is it better to buy a new dishwasher? It is 8 years old. Thank you
1 Answer Yvonne, the control panel A00035004 would be used with the model number provided. Read More...