Jerry February 25, 2021 for Model Number WSSH300G0WW How do you access the right hand lower screw? There is no room to get in there and remove it? The Tube, Item 44 is blocking it? Thanks.
1 Answer Jerry, You would just need to remove the dispenser hose if you are unable to get the lower right-hand screw out. The hose should just be held on with a clamp. Read More...
Jerry February 24, 2021 for Model Number WSSH300G0WW How do you install the Washer Valve Water Assembly? Do you only remove this assembly by only removing the two screws? Or is there more to it?
1 Answer Jerry, the water valve 134371220 would be removed by unscrewing the two screws from the dispenser housing, moving the valve assembly towards the back, lifting up and pulling it forward. Read More...
Carol November 24, 2020 for Model Number WH13X10030 This part # is for a GE front loading washer water intake valve. When the photo comes up, it is identical to the frigidaire front loading washer intake valve, but it says that they are not compatible...same size, same components, how are they not compatible. I'm not a mechanic or a plumber, just trying to get my washer fixed without breaking the bank
1 Answer Carol, The reason that the part is showing as not being compatible is that this valve is not on the frigidaire parts list and so it would not be considered compatible. We cannot say that this will work for the frigidaire model but you can certainly try to see if it is correct. Read More...
Celia October 09, 2019 for Model Number ATF8000FS1 I was using my washer and didn’t go check it till the next day. The timer still showed 1 minute on it. I pressed the cancel button and everything went off. I tried to use it today and the controls all light up but no water starts into the machine. What could the problem be?
1 Answer Celia, based on the information provided, the most likely issue would be the main control 134743500. This can be tested by activating a cycle and testing the valves for 120VAC (valve tested is based on water temperature selection). If the corresponding valve does not receive 120VAC, then the main control would be the issue. If the valve does receive 120VAC, then the valve 134371220 would be the issue. Read More...
Paul August 08, 2019 for Model Number wssh300goww It looks like i stripped the plastic end where the hose attaches to the washer. is there a way to re thread it or do I have to replace the water valve?
1 Answer Paul, Sorry, but, Replace the valve assembly. the fill hoses won't seat and tighten correctly, and you'll have a constant leak, sooner or later, causing more damage. This time, install the hose on the left first, hand tighten the connection, then add a 1/2 turn with a pair of pliers, then repeat the procedure for the hose on the right, turn on the faucets and check for drips or leaks(add 1/4 turn at a time if necessary) wait a few minutes then start the washer and let it fill, while checking for drips or leaks. Thanks, Read More...
Bertha July 07, 2019 for Model Number FAFW3801LW0 If my washer will not quit running water in it and won't spin the water out, what is the problem?
1 Answer Bertha, if you unplug the washer and the water stops, then the most likely issue would be with the water level sensor 134762000. If the water does not stop when you unplug the unit, then the issue would be with the water valve 134371220. Read More...
Matt July 13, 2018 for Model Number frigidaire affinity Washer quit working. It won't fill up with water when it should and by the end of the load, the water won't drain. I replaced the drain pump and it still won't work right. The clothes are still wet and the timer says 1 minute remaining and that is after 3 hours. Is it the door lock or the inlet valve? What part should I replace next before I shoot if full of holes?
1 Answer Hello Matt, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can provide a proper diagnosis and recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Mike S. June 27, 2017 for Model Number frigidaire washer Hi - I bought a water inlet valve for my Frigidaire washer and I need to the two grommets that go on the end of the valve. Can you please give me the part number so I can order two of them please? Thanks Mike
1 Answer Hello Mike! If you are referring to the gasket that sits between the dispenser tray and your valves, that would be part number 134371300. If you need further assistance locating a part, please feel free to give us a call at 877-477-7278. Thank you! Read More...
Bill May 07, 2017 for Model Number WSSH300G1WW The VALVE WATER ASM (WH13X10030) was cracked. The replacement part came with one black cover over the cold "nipple" that inserts directly into the dispenser. I've seen WH13X10030 part photos where this same black cover was on one side, both sides, or neither side. (A Google Image search of WH13X10030 will show all.) Confusing. Is this just a protective cover that should be removed from any/all sides before installation? Thanks for your help, in advance. Bill
1 Answer Bill, Based on what you are describing the black piece would be a protective cover and would be removed before installation. Read More...
Gerri February 09, 2017 Just replaced the water inlet valve, not getting error codes. Washer started like I thought normal started to fill but drum is not spinning, adds little more water but not spinning.
1 Answer Hello Gerri. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...