Cheyenne June 06, 2018 for Model Number JGB800DEP2CC I want to convert from Ng to Lp what parts do I need?
1 Answer Cheyenne, There would be no LP conversion kit for this and you would need to get individual orifice WB28K10215 for left rear, WB28K10839 right front, WB28K10031 right rear and WB28K10023 for the left front. For the oven tighten orifices to snug and open air shutters all the way on the burner, then flip cap on regulator from NAT to LP. Read More...
Erik February 12, 2018 for Model Number JDRP548WP02 I need to convert my range back to NG from propane and the original spud orifices are missing. Do you sell these? If so what do I need to order to convert all 6 burners over? Thank you!
1 Answer Erik, You will need to get 2 of orifice W10340424 for left front and right front burner, 2 of orifice W10819958 for left front and right front burners, 3 of orifice W11051480 for the left rear, right rear and center front burners and 1 of orifice W10791075 for the center front burner. Read More...
Jim November 30, 2017 for Model Number ge #jgb660dejww I need to convert from natural gas to LP. I need to know what I need to order.
Jim November 30, 2017 for Model Number ge #jgb660dejww I need to convert from natural gas to LP. I need to know what I need to order. Thank you
Kathleen L. October 30, 2017 for Model Number JGB605SETSS-SST My gas range was converted to Lp. I now need to convert back to natural gas. What natural gas orifice numbers do I need? There is also a middle grill so there should be 5 orifices needing change. What are they and what needs to be changed in the bake compartment?
1 Answer Hello Kathleen, You will need to order WB28K10817 RR, WB28K10815 LR, WB28K10813 LF, WB28K10812 RF, and WB28K10289 Central Burner. As a note, These parts have to be ordered to obtain the orifices. Unless there are problems with the tubes, the orifices can be removed from the tubes and installed in place of the LP orifices. The orifice hoods just below the bake and broil burners can be adjusted with a 1/2 inch open end wrench by turning them 1 1/2 to 2 turns counterclockwise. You will then need to go to the regulator and convert it by removing the plastic cap and flipping the large nut, (be sure to re-install the plastic cap). If there is any yellow tipping in the flames, these can be adjusted out by adjusting the air shutters on the base of the burners. Read More...
Josh G. August 31, 2017 for Model Number JGB605DET2BB I converted my stove to LP when I purchased it, and have no idea where the NG orifices are. What parts would I need to buy to replace the 5 burners, the broil, and the bake burners? Thanks
1 Answer Hello Josh, From the manufacturers' parts list, you would need to order one WB28K10289 for the center, one WB28K10812 for the RF, one WB28K10813 for the LF, one WB28K10815 for the LR, and one WB28K10817 for the RR. The broil hood is WB28K10310 and the bake hood is WB19K10078. Any yellow tipping is adjusted out with the air shutters. Read More...
Kim Baker July 23, 2017 for Model Number JGBS66EEKES I dropped one of the orifices down in the burner when I installed my new range. I need to replace only one and it is for an LP gas burner 15,000 BTU, size 1.14. Do you sell this part by itself or do I have to buy the whole set? Thank you.
1 Answer Hello Kim! The manufacturer list part number WB28X26625 as the lp orifice for the front left burner, hope this helps! Read More...
Phil K January 06, 2017 for Model Number JGC8536ADS I have a Jenn-Air cooktop and I need to replace the LP spuds with natural gas. There are 3 different sizes for the 5 burners. Can you tell me which spuds I need?
1 Answer Hello Phil. Left rear surface burner (9,200 BTUs). WP7527P002-60 Left front surface burner 5,000 BTUs. 74009553 Center surface burner (15,000 BTUs). WP7527P004-60 Right front surface burner (12,500 BTUs). WP7527P003-60 Right rear surface burner 5,000 BTUs. 74009553 Read More...
David July 10, 2016 for Model Number JGP963SEK1SS My orifices are: LF=162N III LR=150N II Mid=107N I RR=107N I RF=193N X I live at 500' elevation (near sea level) I found AP3792977 LP (LR?), AP3793136 LP (LF?), AP2026919 LP (Mid & RR?), AP2626673 LP (RF?) please verify if these are correct parts to change out? - Is there a master kit to change to LP for this unit?
1 Answer David, It appears that you have all the correct part numbers for the LP orifices. They do not list this as a kit. Read More...
Ge Oven User March 15, 2016 for Model Number GE JGB820SEP2SS We are looking to switch our GE JGB820SEP2SS over from Propane to Natural Gas, we have misplaced the orifice that came with the oven and I am looking to purchase them. Any insight would be appreciated! thanks!
1 Answer Hello GE Oven User, You will need to order WB28K10596 for the center burner, WB28K10424 for the right front, WB28K10590 for the front left, WB28K10592 for the left rear, and WB28K10390 for the right rear. Convert the regulator as follows: Remove the storage drawer, kickpanel and if applicable the access panel to access the regulator. (Some models will have a metal shield protecting the regulator that must be removed for conversion and reinstalled when conversion is complete.) The pressure regulator is located in the lower, left hand rear corner of the range as viewed from the front. b. Unscrew the plastic-protected hex-nut cap. c. Completely remove the protective plastic cap off the threaded metal cap. d. Turn the metal cap so the type of gas being converted to is displayed and replace the protective plastic cover. e. Screw the hex-nut cap back into the regulator. (Do not over tighten). To convert the bake and broil burners to natural, use a 1/2" wrench to turn the lower burner orifice hood counter-clockwise (When viewed from above) until it is snug with the base, approximately 2 1/2 turns. (To prevent damage when converting back to Natural Gas, do not over tighten the hood.) Read More...