Rtw4340sq0 Type 111 Parts

This water inlet valve controls the flow of household water into the dishwasher at the start of a cycle. Replacing a weak, stuck, or leaking valve restores proper filling performance and helps prevent fill-related errors and leaks. What it does:

• Opens and closes electrically to regulate water entering the dishwasher
• Helps ensure correct fill level and timing for each cycle
• Common failure symptoms: won't fill or slow fill, water seeping into tub when off, external leak at valve connections, loud buzzing/chattering during fill
• May set fill or water supply-related error codes on some models

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Have a towel or shallow pan ready for residual water when removing lines
• Transfer any original mounting hardware or fittings from the old valve as needed
• Inspect/clean the inlet screen and flush the supply line; check all connections for leaks after installation

This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:

• Holds the motor firmly in place within the assembly
• Maintains alignment for smooth, quiet operation
• Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
• Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor

• Includes 1 motor retainer.

• Disconnect power; turn off water supply.
• Access the motor area and support the motor before removing the old retainer.
• Inspect mating parts and seals; replace any damaged components.
• Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.

This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.

• Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
• Replaces a lost, worn, or damaged anti-rattle fastener
• Helps maintain proper alignment and prevents vibration-related wear
• Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet

• Disconnect power before servicing; for gas appliances, shut off the gas supply
• Access the mounting point and remove the loose or damaged screw
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the bracket/clip before reassembly

This upper agitator—also called the clothes mover—is the top section of the agitator in select top-load washers. It works with the agitator cam and dogs to roll laundry over during wash strokes. Replace if cracked, stripped, or no longer engaging. What it does:

• Provides the upper vanes that lift and roll clothes for proper turnover during agitation
• Transfers one-way motion from the cam/dogs to the top section of the agitator
• Helps address symptoms like the top section free-spinning, poor turnover/cleaning, rattling/loose feel, or visible cracks/broken fins

• 1 upper agitator (clothes mover)

• Unplug the washer and turn off water before servicing
• Remove the dispenser and cap to access the center fastener; lift out the agitator assembly
• Separate the old upper section from the cam, seat the new clothes mover fully on the splines, and reassemble
• Hand-check for one-way engagement of the top section before running a test cycle

Push-in.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

Timer dial assembly that replaces a damaged or worn selector on the control panel, restoring clear, reliable cycle selection and easy manual control without replacing the entire timer mechanism. What it does

• Provides the tactile selector that mounts to the timer shaft so you can set and advance appliance cycles.
• Restores smooth, positive rotation and visible cycle position markings for accurate selection.
• Replace when the dial is cracked, stripped, loose, missing, or spins without turning the timer.
• Improves usability and appearance of the control panel when original dial is worn.

• Disconnect power to the appliance before beginning any repair to prevent shock or injury.
• Access typically requires removing the control knob or front control panel; follow for correct disassembly.
• Handle control shafts and nearby wiring carefully; test dial function and run a short cycle after reassembly to ensure proper operation.