Shs863w Parts

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This outer door is the exterior front panel that restores the appliance's appearance and protects internal door components. It provides a clean finished look while helping keep controls and inner parts covered and secure. What it does

• Replaces a dented, scratched, or corroded front door panel to improve appearance
• Protects inner door assembly, insulation, and controls from moisture and impact
• Helps maintain proper alignment so the door opens and closes smoothly
• Can reduce drafts or light gaps caused by a damaged outer panel

• One outer door

• High-level replacement; door removal and partial disassembly are typically required
• Support the door while removing fasteners to avoid dropping or bending the panel
• Keep track of screws, brackets, and trim pieces; transfer any attached components to the new panel
• Disconnect power to the appliance before starting and follow all safety precautions

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

This base panel covers the lower-front opening of the dishwasher, protecting internal components and completing the finished look. Replace a bent, rusted, or missing panel to restore proper shielding and help reduce vibration and noise.

• Covers the bottom-front opening of the dishwasher
• Helps protect wiring, hoses, and moving parts from debris and accidental contact
• Contributes to sound damping and a clean, finished appearance
• Typical indicators: panel is dented, rusted, rattling, loose, or missing

• Disconnect power and turn off water supply before servicing
• Remove the mounting screws and support the old panel as you take it off
• Align the new panel and secure with the original hardware; do not overtighten
• Restore power and verify the panel is secure and free of vibration

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This trim strip finishes and protects the exposed edge of the appliance where it installs, helping secure adjacent panels and giving a clean, finished look. Replacing a damaged strip can improve fit and appearance.

• Provides a finished edge and helps secure panels or covers in place
• Helps prevent gaps that can collect debris
• Common fix when the existing strip is cracked, bent, loose, or missing
• Reduce rattles or vibrations caused by an ill-fitting trim piece

• Disconnect power and shut off any utilities before servicing
• Note orientation/position of the old strip before removal
• Press or fasten the new strip into the same mounting points; do not force
• After installation, recheck clearances and panel alignment

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

The Insert is an OEM component specifically designed for select Bosch dishwashers. Located inside the tub basin, the tines provide the necessary friction to help clean dishes. 

Causes of a bad insert can include mineral buildup that prevents proper movement or damage from dropped utensils that have bent the tines out of place.

Symptoms of a bad insert include:

• Dishes still feeling dirty after the wash cycle   
• Rust or mineral deposits visible on the tines
• Tines that are bent or missing which reduces cleaning surface area

Replacing the insert with this OEM Bosch part restores optimal cleaning performance. Compatible with 300 series models, it features stainless steel construction that withstands corrosion from detergents. This replacement insert is warranted to perform as the original Bosch design for reliable dish cleaning.
 

The Dishrack Roller is an OEM replacement part for Bosch dishwashers. Located inside the tub, this roller assists with moving upper and lower dishracks in and out during operation. 

Causes of failure are prolonged exposure to detergent residues combined with repeated rolling impact stresses absorbing dishrack weight for tens of thousands of cycles.

Symptoms of a worn or damaged dishrack roller include:  

• Difficulty fully extending or retracting dishrack shelves  
• Rack skew or tilting sideways instead of moving smoothly
• Grinding or scraping noises heard from the tub area  
• Dishes not lining up properly to receive spray patterns

This genuine Bosch roller is also compatible with Thermador and Gaggenau models.