How to replace Bosch dishwasher start button 00616599

Is your Bosch dishwasher not starting as it should? A faulty start button could be the culprit, leaving you with piles of dirty dishes. Luckily, swapping out the damaged button is a straightforward task that you can tackle in no time—check out the step-by-step video guide below to learn how.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

The start button is located on the control panel of a Bosch dishwasher and helps the user initiate the wash cycles. Over time, the start button may become worn out or damaged, which can cause it to become unresponsive when pressed or stuck in the “ON” position, both of which can prevent the dishwasher from starting.

Fortunately, you can easily change out the old start button for a new one, which can save you a significant amount of time and money.

Let’s walk through the replacement process so you can get your dishwasher back to its normal self.

You can find a replacement start button here. If you need other replacement parts for your Bosch dishwasher, just enter your model number at AppliancePartsPros.com to find them. It’s that easy! Most orders arrive in just two business days, and we have thousands of guides to show you how to install your new parts.

Watch here: How to replace Bosch/Thermador/Gaggenau Start Button 00616599

What you need

• Torx 20 screwdriver
• Large flathead screwdriver
• Small flathead screwdriver
• New start button (make sure it’s compatible with your specific dishwasher model before installing)

Disclaimer: The specific tools required may vary depending on the model of your appliance and the type of fasteners used on it. Always consult the user manual or refer to any specific instructions provided by the manufacturer for the recommended tools for your appliance model.

Read more: Must-Have Tools for Appliance Repair – DIY For Beginners

Check part compatibility

Before you replace the start button, make sure you have an OEM part that’s compatible with your specific dishwasher model. To do this, you’ll need to find the appliance model number.

The model number will say MOD or Model before the numbers and is typically found on a sticker or a metal plate in one of the following locations:

• On the side wall or the door frame
• On the back or bottom of the dishwasher
• On the control panel or console

Once you’ve found the model number, write it down or take a clear photo of it for reference.

Next, visit AppliancePartsPros.com, where you can enter your model number to check if the start button is compatible with your model.

Read more: How To Find Your Appliance’s Model Number

Safety precautions

When working on any appliance, remember to keep safety first. Here are some tips to keep in mind:

• Always power off and unplug your appliance or switch off the circuit breaker before you attempt any maintenance or replacement work. This keeps you safe by eliminating any risk of electric shock.
• If the appliance has recently been used, give it plenty of time to cool down before working on it.
• Turn off the water supply at the outlet before beginning repairs. Keep towels ready to catch any residual water in the system when removing parts.
• Take your time while working to prevent accidents and personal injuries. Rushing is the enemy of precision.
• Work in a well-lit area so you can see and access appliance parts.
• Keep your workspace free of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with wet hands. Make sure the work area is completely dry.
• Check the user manual to see if there are specific installation or safety instructions related to your appliance or replacement part.
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause personal injury.
• Wear insulated work gloves to protect your hands from sharp metal parts and debris.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Always take photos or make a note of wiring terminals or other connections before disconnecting them to make reassembly easier.

Read more: How to clean dishwasher spray arms

How to replace the start button

Follow these steps to replace a faulty start button on a Bosch dishwasher.

1. Unplug the dishwasher from the power outlet.
2. Open the door of the dishwasher.
3. Use a Torx 20 screwdriver to remove the six screws from the top of the control panel.
4. Lift the door and gently pull off the control panel to detach it from the dishwasher.
5. Find the wiring harness plugs that are connected to the control panel.
6. Press the locking tab on each wiring harness plug and pull each one out to disconnect them.
7. Use a flathead screwdriver to press on the locking tab at the bottom of the control board plug and remove the plug from the control board.
8. Slide the harness out and open the two tabs to remove the plug from the panel.
9. Place the control panel on a table or a flat surface.
10. Use a small flathead screwdriver to open the tabs on the door handle.
11. Rotate the door handle and remove it from the control panel.
12. Use a flathead screwdriver to carefully press on the tabs that hold the user interface control board.
13. Lift the user interface control board and remove it from the control panel.
14. Press the old start button inwards and pull it out to remove it from the control panel.
15. Place the two ends of the new start button into the mounting bracket on the control panel.
16. Reinstall the user interface control board into the control panel by aligning the tabs and pressing it down until it locks into place.
17. Align the two tabs of the door handle with the cutouts on the control panel.
18. Press the door handle down until the tabs lock into place.
19. Reconnect the wiring harness plugs by inserting them into their respective sockets on the control panel. Make sure each plug is fully inserted and secure by pressing the locking tab.
20. Slide the harness back into place and close the two tabs to secure the plug to the panel.
21. Open the door of the dishwasher and position the control panel.
22. Secure the control panel to the dishwasher with the six screws.
23. Close the dishwasher door.
24. Plug in the dishwasher’s power cord.
25. Run a test cycle to check for any problems.

Read more: What cycle should I run my dishwasher on?

Additional information

Thanks for reading! We hope this guide helped you replace the start button on your Bosch dishwasher.

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Follow us on Facebook, Twitter and Instagram to see our latest repair guides!