How to replace the light frame on an LG refrigerator

Is your refrigerator’s light frame damaged, leaving you in the dark? Whether it’s from accidentally leaving the door ajar or wear and tear, fixing your LG refrigerator’s light frame is easier than you might think. Ready to illuminate your way to a DIY fix? Scroll down to watch our step-by-step video guide and get started!

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

On an LG refrigerator, the light frame supports the lights and the control board in the refrigerator section. Over time, leaving the refrigerator door open for an extended period or a faulty switch can lead to damage to the frame. 

Fortunately, this repair is quick and straightforward, and with just a few steps, you’ll have your refrigerator’s light frame replaced in no time. On average, the entire repair process should take around 30 minutes to an hour, depending on your level of experience with repairs. So let’s get started and bring back the brightness to your refrigerator!

Watch here: How To: LG/Kenmore Light Frame 3110JA1096A

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

Tools needed

• Flathead screwdriver
• Phillips screwdriver
• Heat gun

Safety precautions

• Always power off and unplug your appliance or switch off the circuit breaker before attempting any maintenance or replacement work. This keeps you safe by preventing any risk of injury from electric shock.
• Wear insulated work gloves to protect your hands from sharp metal parts, pinching hazards and debris.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Take your time and don’t rush while working to prevent accidents and personal injuries.
• Work in a well-lit area so you can clearly see and access the interior parts.
• Clear your workspace of clutter and other obstacles. Keep children and pets away from the work area.
• Check your user manual to see if there are specific installation or safety instructions for your part or appliance. 
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause injury.
• Wear safety glasses when working with chemicals, dust or cleaning large debris to prevent injury. 

Replacement steps

Disassembly

1. Open the refrigerator door. Remove the top shelves to create space for disassembly.
2. Insert a flat blade screwdriver into the openings in the front of the light lens.
3. Press the locking tabs with the screwdriver and pull down on the lens to remove it.
4. Unscrew the light bulbs by turning them counterclockwise.
5. Locate the two screws that hold the light frame in place.
6. Use a Philips screwdriver to unscrew and remove the two screws.
7. Drop the front of the light frame down and pull the rear tabs out.
8. Press the locking tabs and disconnect the two wire plugs.
9. Take the light frame assembly to a work table.
10. Push in the tabs on the sides of the heat shield.
11. Lift the heat shield up and slide it out of the two rear retainers.
12. Use a heat gun to heat up the touchpad surface without melting it.
13. Start peeling the touchpad off the frame using a flat blade screwdriver, being careful not to break it.
14. Remove the three Philips screws that secure the display control board.
15. Carefully remove the display control board together with its frame.

Installation

1. Insert the display control board assembly into the new light frame.
2. Push the assembly in until it locks into place.
3. Secure the display control board with the three Philips screws.
4. Install the heat shield under the two rear retainers.
5. Press down on the heat shield to lock the tabs.
6. Bring the light frame assembly back to the refrigerator.
7. Reconnect the two wire plugs.
8. Insert the rear tabs of the light frame into the cutouts in the refrigerator.
9. Lift the front of the frame up and align it with the screw holes.
10. Secure the light frame with the two Philips screws.
11. Carefully place the touchpad overlay back onto the frame.
12. Install the light bulbs by turning them clockwise.
13. Install the light lens with the two rear tabs into the cutouts.
14. Press the lens up to lock it in place.
15. Reinstall the top shelves. Close the refrigerator door.
16. Plug the refrigerator back in. Test the refrigerator to check for any problems.

Additional information

Thanks for reading! We hope this guide helped you replace the light frame on your LG refrigerator. 

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter and Instagram to see our latest repair guides!