How to replace KitchenAid stand mixer motor housing seal WP240775-1

Is your KitchenAid stand mixer causing more headaches than homemade brownies? A worn or damaged motor housing seal could be letting in debris that threatens your mixer’s motor. Fortunately, our quick guide—with an easy-to-follow how-to video below—will have you swapping it out in no time, ensuring your mixer is back in action for your next culinary creation.

Need a part?  Search below using your appliance model number to find exactly what you need:

The motor housing seal on a KitchenAid stand mixer is located at the back of the mixer and helps prevent leaks and debris from entering the motor housing that could damage the internal motor. Over time, this seal may become worn or damaged, which could lead to motor issues if something were to find its way into the housing.

The repair is relatively straightforward and should only take a few minutes for you to complete yourself.

You can find a motor housing seal WP240775-1 here. If you need other replacement parts for your KitchenAid stand mixer, just enter your model number at AppliancePartsPros.com to find them. It’s that easy! Most orders arrive in just two business days, and we have thousands of guides to show you how to install your new parts.

Watch here: How To: Whirlpool/KitchenAid/Maytag Motor Housing Seal WP240775-1

What you’ll need

• Phillips screwdriver
• Flathead screwdriver
• Needle nose pliers
• Replacement motor housing seal (make sure it’s compatible with your specific model before installing)

Disclaimer: The specific tools required may vary depending on the model of your appliance and the type of fasteners used on it. Always consult the user manual or refer to any specific instructions provided by the manufacturer for the recommended tools for your appliance model.

Read more:  How to fix a KitchenAid stand mixer that won’t start

Check part compatibility

Before you replace the motor housing seal, make sure you have an OEM part that’s compatible with your specific mixer model. To do this, you’ll need to find the appliance model number.

The model number will say MOD or Model before the numbers and is typically found on a sticker or a metal plate in one of the following locations:

• On the underside of the mixer’s base
• On the back of the mixer’s head or motor housing
• On the side of the mixer’s base

Once you’ve found the model number, write it down or take a clear photo of it for reference.

Next, visit AppliancePartsPros.com, where you can enter your model number to check if the new motor housing seal is compatible with your model.

Read more:  Kitchenaid Stand Mixer Attachments To Try

Safety precautions

When working on any appliance, remember to keep safety first. Here are some tips to keep in mind:

• Always power off and unplug your appliance or switch off the circuit breaker before you attempt any maintenance or replacement work. This keeps you safe by preventing any risk of electric shock.
• If the appliance has recently been used, give it plenty of time to cool down before working on it.
• Take your time while working to prevent accidents and personal injuries. Rushing is the enemy of precision.
• Work in a well-lit area so you can clearly see and access appliance parts.
• Keep your workspace free of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with wet hands. Make sure the work area is completely dry.
• Check the user manual to see if there are specific installation or safety instructions related to your appliance or replacement part.
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause personal injury.
• Wear insulated work gloves to protect your hands from sharp metal parts and debris.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.

How to replace the motor housing seal

Follow these steps to switch out the motor housing seal in your KitchenAid stand mixer.

Step 1: Remove the old motor housing seal

1. Unplug the mixer from the outlet.
2. Remove the beater by lifting it and turning it clockwise.
3. Remove the bowl by lifting it and pulling it out.
4. Use a Phillips screwdriver to remove the screw on the back cover of the mixer.
5. Rotate the cover down and lift it off its mounting legs. Set the cover aside.
6. Use a Phillips screwdriver to remove the two screws that hold the trim overlapping and covering the edge of the seal.
7. Carefully flex the trim away and lift it off, then set it aside.
8. Find the seal, which is located around the speed control assembly.
9. Use a Phillips screwdriver to remove the ground wire.
10. Remove the wires on each side of the seal. Use a small flat-head screwdriver to help pop them off.
11. Remove the black wire on the bottom and the white wire.
12. On the other side, remove the white wire on the bottom and the red wire above it.
13. Once all the wires are disconnected, move them away from the seal.
14. Carefully lift the old motor housing seal out. If any wires get caught, carefully move them out of the way.
15. Pull the motor housing seal off the mixer.

Step 2: Install the new motor housing seal

1. Note the cutouts with perforation to fold the new motor housing seal.
2. Place the bottom of the seal and get the corners behind the housings.
3. Rotate the top of the seal up and push it all the way on.
4. Reattach the wires starting with the ones on the side where the red wire was on top and the white wire was on the bottom.
5. On the other side, use a Phillips screwdriver to connect the ground wire.
6. Connect the black and white wires.
7. Look over all the wires to make sure they’re securely connected. If necessary, use a small screwdriver to gently push them on.
8. Put the trim band back on. Carefully line up the trim band on the mixer and hook each end around the back side.
9. Use the Phillips screwdriver to insert the screws and secure the trim band in place.
10. Put the cover back on by checking that the edge of the seal goes into the cutout and that the feet go into the openings.
11. Lift the cover and make sure it’s not caught on any wires, then use the Phillips screwdriver to insert the screw.
12. Put the bowl back on by lining up the pinholes and setting it down. Lock it in place.
13. Put the beater back on by lining up the shaft with the opening and making sure the locking pin goes in the slot. Lift it into place and lock it on.
14. Plug the mixer back in and test it to check for any problems.

Read more: How To Clean And Maintain Your Stand Mixer

Additional information

Thanks for reading! We hope this guide helped you replace the motor housing seal on your KitchenAid stand mixer.

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter and Instagram to see our latest repair guides!