Frigidaire refrigerator ice crusher blade 241684109 repair guide

Is your Frigidaire or Electrolux refrigerator failing to crush ice as smoothly as it should? Don’t worry—your days of dealing with chunky ice dispensations are over. With our step-by-step guide and handy how-to video, you’ll easily replace the faulty crusher blade and get your ice dispenser back in perfect working order.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

If you notice your Frigidaire or Electrolux refrigerator is not properly crushing ice, the issue may be a worn or damaged ice crusher blade. Replacing this part is an easy do-it-yourself repair that can restore normal ice dispensing function. We’ll walk through the full process of removing and replacing Frigidaire/Electrolux ice maker crusher blade #3 (241684109).

Watch the full repair here!

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

Materials needed

To successfully complete this repair, it’s important to gather the necessary tools and parts beforehand. Safety is also a crucial aspect to consider when working with appliances. Follow these guidelines to ensure a smooth and secure repair process:

• Phillips head screwdriver
• Flathead screwdriver
• Quarter-inch nut driver
• Pliers
• Replacement ice crusher blade #3 (part # 241684109)

Safety precautions   

Safety should always be a priority when working on any appliance. Here are a few practical tips to help you stay safe:

• Turn off the power to the appliance by unplugging it or switching off the circuit breaker before starting any maintenance or repairs. This protects you from the risk of electric shock.
• Wear insulated gloves to shield your hands from sharp edges, pinching hazards, or debris.
• Work at a steady pace and take your time to avoid accidents or injuries.
• Make sure your workspace is well-lit so you can clearly see and access the parts you’re working on.
• Keep the area clear of clutter, and ensure children and pets stay out of the workspace.
• Never handle internal parts with wet hands. Check that both your hands and the work area are completely dry.
• Refer to your appliance’s user manual for any specific instructions or safety guidelines related to the part or repair.
• Handle parts gently to avoid damage to the appliance or potential injuries from applying too much force.
• Use safety glasses when dealing with chemicals, dust, or large debris to protect your eyes from harm.
• If the appliance was recently used, give it enough time to cool down before working on any heated components.
• Take photos or notes of wiring connections and terminals before disconnecting anything to make reassembly easier.
• Avoid touching exposed wires or terminals. If you must handle wires, use non-conductive tools or wear insulated gloves to minimize the risk of electrical shock.

Removal Steps

1. Open the freezer door, locate the ice bucket, and lift it upwards to detach it from the icemaker assembly. Be careful not to spill ice. Place it on a towel on the counter or floor to protect surfaces.
2. On the back of the bucket, locate four Phillips head screws (two on top, two on bottom). Remove them using a Phillips screwdriver and carefully pry off the plastic cover. Set the cover aside safely.
3. Stand the bucket upright. Use a flathead screwdriver to pry off the e-clip near the crusher blade assembly. Remove the metal washer underneath and set both aside.
4. Use a 1/4-inch nut driver to remove the two screws holding the auger cover in place. Unhook the connecting bar from the freezer door bracket and swing it out of the way. Lift off the cover carefully and set it aside.
5. Try loosening the large nut by hand. If stuck, use pliers gently to break it free. Unscrew it completely and set it aside.
6. Lift the old #3 crusher blade straight off the auger shaft and discard it. Compare it to the new blade to confirm it’s the correct replacement.

Installation Steps

1. Place the new #3 blade onto the auger shaft, ensuring it aligns as the original and sits flush.
2. Reinstall the auger nut by hand and tighten it snugly. Use pliers if necessary, but do not overtighten.
3. Position the auger cover back over the crusher assembly. Reattach the connecting bar to the freezer door and secure the cover screws using your nut driver.
4. Slide the metal washer back into place. Use the flathead screwdriver to snap the e-clip securely onto the shaft.
5. Align the plastic cover on the back of the ice bucket and secure it with the four Phillips screws.
6. Slide the ice bucket back into position on the freezer’s rails. Ensure it’s seated properly and closes smoothly.
7. Close the freezer door and plug the refrigerator back in to restore power.

Where To Find Us 

If you need any replacement parts for your appliances, you can enter your model number at AppliancePartsPros.com to locate and order them quickly. Most orders arrive in just two business days, and we have tons of great information in our repair help section and YouTube videos to help you troubleshoot.

Stay connected with the latest DIY tips, tutorial videos, and repair guides by following us on Facebook, Instagram, and Twitter. We love hearing about your repair stories and successes. If you need more help or want personalized guidance, feel free to reach out. We’re ready to help you take on your next project with confidence!