GE Dishwasher Door Gasket WD08X10057 DIY Replacement Guide

Is your dishwasher turning your kitchen floor into a slip-and-slide? A leaky door gasket might be to blame! Don’t worry—swapping it out is simpler than you think, and we’ve got a step-by-step guide to walk you through it. Plus, check out the how-to video below to see exactly how it’s done.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

Replacing a worn or damaged dishwasher door gasket is an easy do-it-yourself project that can save you money on repair bills. A faulty door gasket allows water to leak out during the wash cycle, potentially causing damage to your floors and cabinets. We’ll walk through the entire process of replacing a dishwasher door gasket, using a GE dishwasher and part #WD08X10057.

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

Watch: How to Replace door gasket

Why Replace the Door Gasket?

The rubber gasket around your dishwasher door creates a water-tight seal between the tub and the door. Over time, through regular use, the gasket can become brittle, cracked, or torn. Typical signs that your existing door gasket needs to be replaced include:

• Visible cracks or tears in the rubber
• The gasket feels overly stiff or spongy
• Dishes aren’t getting fully cleaned
• Puddles of water on the floor after running the dishwasher

Replacing a worn-out gasket is a fast and easy fix that can stop leaks and improve washing performance.

What You’ll Need

Replacing a dishwasher door gasket is a straightforward project that requires minimal tools and parts. Here’s what you’ll need to complete the repair:

• New door gasket – Make sure you order the correct replacement gasket for your dishwasher make and model. 
• Small flathead screwdriver – To pry off the old gasket from the door frame.
• Gloves – Rubber gloves will protect your hands while handling the gasket.
• Towels – To soak up any water drips or spills during the repair.

Safety Tips

When servicing any appliance, it’s critical that you take proper safety precautions:

• Disconnect power supply – Unplug the dishwasher or shut off power at the circuit breaker before starting.
• Turn off water supply – Locate the water shut-off valve underneath the sink and turn it off before replacing the gasket.
• Protect floors & surfaces – Place towels underneath the dishwasher to avoid damage from leaks/drips.

Taking these preventative measures will allow you to safely replace the gasket without risk of shock or water damage.

Step-by-Step Installation Guide

Follow these step-by-step instructions to successfully replace your GE dishwasher’s door gasket.

1. The first step is to remove the upper and lower dish racks to gain better access to the door. Pull out both racks and set them aside. If your model has a third upper rack, remove that as well.
2. Using a flathead screwdriver, wedge the tip underneath the existing gasket and gently pry it out of the channel around the door frame. Take care not to damage the door panel. Remove the entire gasket all the way around.
3. Once the old gasket is removed, inspect the door frame channel that held the gasket. Use a damp rag to wipe away any dirt, debris, or old soap buildup. The new gasket will install more smoothly on a clean surface.
4. Examine the replacement gasket and note the molded corners and notch in the middle. The notch indicates the center point that will align with the door latch.
5. Run the gasket under warm water to make it more pliable for installation.
6. Line up the center notch with the door latch. Working on one side of the door, fit the gasket into the frame channel, pressing it firmly into place with your fingers. Take care not to stretch or twist the gasket.
7. Continue around to the opposite side, fitting the gasket into the frame channel in the same manner. Again, press the gasket firmly into place.
8. The gasket may need to be stretched slightly to fit around the corners of the door. Work slowly and gently pull the gasket while pressing it into the frame. Improper pulling can tear or deform the gasket.
9. Once fully inserted, run your fingers around the entire gasket, pressing it into the channel to ensure it’s seated properly within the grooves. Visually inspect from inside the tub to confirm a complete seal.
10. With the new gasket fully installed, slide the dish racks back into place.
11. The last step is to reconnect your dishwasher. Turn the water supply back on, plug the unit in or turn on the circuit breaker. Run a test cycle to verify no leaks around the freshly replaced gasket.

And that’s it! With a little patience, you can complete this repair yourself and save the cost of a service call.

Where To Find Us 

If you need any replacement parts for your appliances, you can enter your model number at AppliancePartsPros.com to locate and order them quickly. Most orders arrive in just two business days, and we have tons of great information in our repair help section and YouTube videos to help you troubleshoot.

Stay connected with the latest DIY tips, tutorial videos, and repair guides by following us on Facebook, Instagram, and Twitter. We love hearing about your repair stories and successes. If you need more help or want personalized guidance, feel free to reach out. We’re ready to help you take on your next project with confidence!