How to replace a KitchenAid stand mixer hub gear kit W11192794

Is your KitchenAid stand mixer making peculiar noises or showing signs of uneven mixing? Don’t be quick to retire it just yet! Dive into our step-by-step guide, complete with a handy how-to video below, to easily replace the hub gear kit and restore your mixer to its former glory.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

On a KitchenAid stand mixer, the hub gear kit transfers power from the motor to the attachments so your mixer can mix, knead, grind and more. Over time, regular use can cause the hub gear kit to become damaged. It might be faulty if you notice unusual noises from the mixer, attachments grinding or slipping, a lack of power or uneven mixing.

But don’t toss out your mixer yet! Fortunately, with a few basic tools and some patience, you can repair the hub gear and get your mixer back in working order. So, let’s get started!

You can find a replacement hub gear kit here. If you need other replacement parts for your KitchenAid stand mixer, just enter your model number at AppliancePartsPros.com to find them. It’s that easy! Most orders arrive in just two business days, and we have thousands of guides to show you how to install your new parts.

Watch the full repair here

What you need

• Replacement hub gear kit (make sure it’s compatible with your specific mixer model before installing)
• Large and small flathead screwdrivers
• Large and small Phillips screwdrivers
• Large Phillips driver ratchet
• Hammer
• Punch
• Rubber mallet
• Towels
• Planetary grease WP4176597

Important: The specific tools required may vary depending on the model of your appliance and the type of fasteners used on it. Always consult the user manual or refer to any specific instructions provided by the manufacturer for the recommended tools for your appliance model.

Read more: Why is my KitchenAid stand mixer leaking motor grease?

Safety precautions

When working on any appliance, remember to keep safety first. Here are some tips to keep in mind:

• Always power off and unplug your appliance or switch off the circuit breaker before you attempt any maintenance or replacement work. This keeps you safe by eliminating any risk of electric shock.
• If the appliance has recently been used, give it plenty of time to cool down before working on it.
• Take your time while working to prevent accidents and personal injuries. Rushing is the enemy of precision.
• Work in a well-lit area so you can see and access appliance parts.
• Keep your workspace free of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with wet hands. Make sure the work area is completely dry.
• Check the user manual to see if there are specific installation or safety instructions related to your appliance or replacement part.
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause personal injury.
• Wear insulated work gloves to protect your hands from sharp metal parts and debris.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Always take photos or make a note of wiring terminals or other connections before disconnecting them to make reassembly easier.Read more:  KitchenAid Stand Mixer Attachments To Try

How to replace the hub gear kit

Follow these steps to replace the hub gear kit in your KitchenAid stand mixer.

1. Unplug the mixer from the power outlet.
2. Remove all attachments from the mixer.
3. Lift the beater up, turn it clockwise, and lift it out of the mixer.
4. Lift the bowl straight up and off the base and set both aside.
5. Use a flathead screwdriver and a hammer to carefully tap the trim ring off of the planetary section.
6. Place a punch on the groove pin and tap it out gently with a hammer.
7. Insert a flathead screwdriver under the planetary to pry it loose. Work around it and gently pull it down off the center shaft.
8. Use a Phillips screwdriver to remove the screw holding the rear cover, then lift the cover off its mounting.
9. Disconnect the white and black wires with a small flathead screwdriver.
10. Remove the ground wire’s screw with a Phillips screwdriver, lift the strain relief, and remove the cord.
11. If available, place the mixer onto a U-shaped holder or cushion with towels for support.
12. Tip the mixer over onto the support.
13. If your mixer has a tilt-head, drive out the hinge pin with a punch. If it’s a bowl-lift model, remove the four large Phillips screws with a ratchet.
14. Use a flathead screwdriver to remove the screws from the housing, then gently separate the two halves.
15. Remove the old hub gear and clean off the excess grease.
16. Apply new grease to the new gear, especially on the shaft and teeth.
17. Align the center shaft and mounting pins of the gear housing.
18. Carefully place the upper housing over the lower one and secure it with the screws.
19. Align and place the base, then secure it with the screws. Use a ratchet to make sure they’re tight.
20. Attach the power cord wires and make sure they’re snug.
21. Place the rear cover back on and secure it with the screw.
22. Align the planetary with the center shaft. Adjust as needed and reinsert the groove pin.
23. Attach the trim ring with a rubber mallet to make sure it fits evenly.
24. Place the bowl by aligning it with the pinholes, then lock it into place.
25. Attach the beater by aligning it with the shaft and locking pin.
26. Plug the mixer back in and make sure it works correctly.

Read more: How To Clean And Maintain Your Stand Mixer

Additional information

Thanks for reading! We hope this guide helped you replace the hub gear kit on your KitchenAid stand mixer.

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Follow us on Facebook, Twitter and Instagram to see our latest repair guides!