How to replace Frigidaire refrigerator motor bushing 241563601

Is a noisy refrigerator driving you up the wall? The culprit could be worn-out evaporator motor bushings that have cracked over time, causing your fridge to hum loudly during operation. Discover how you can easily troubleshoot this issue and replace those bothersome bushings with a handy how-to video right below.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

Replacing the evaporator motor bushing on a Frigidaire or Electrolux refrigerator is an easy DIY repair. The evaporator motor bushings absorb vibration from the motor to prevent excess noise. Over time, these bushings can dry out and crack, causing the motor to be noisy during operation. Replacing the old brittle bushings with new ones will restore quiet operation. 

Watch the full repair here

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

What you’ll need

• Flathead screwdriver
• 1/4 inch nut driver
• Replacement evaporator motor bushings (part #241563601)

Safety precautions   

Safety should always be a priority when working on any appliance. Here are a few practical tips to help you stay safe:

• Turn off the power to the appliance by unplugging it or switching off the circuit breaker before starting any maintenance or repairs. This protects you from the risk of electric shock.
• Wear insulated gloves to shield your hands from sharp edges, pinching hazards, or debris.
• Work at a steady pace and take your time to avoid accidents or injuries.
• Make sure your workspace is well-lit so you can clearly see and access the parts you’re working on.
• Keep the area clear of clutter, and ensure children and pets stay out of the workspace.
• Never handle internal parts with wet hands. Check that both your hands and the work area are completely dry.
• Refer to your appliance’s user manual for any specific instructions or safety guidelines related to the part or repair.
• Handle parts gently to avoid damage to the appliance or potential injuries from applying too much force.
• Use safety glasses when dealing with chemicals, dust, or large debris to protect your eyes from harm.
• If the appliance was recently used, give it enough time to cool down before working on any heated components.
• Take photos or notes of wiring connections and terminals before disconnecting anything to make reassembly easier.
• Avoid touching exposed wires or terminals. If you must handle wires, use non-conductive tools or wear insulated gloves to minimize the risk of electrical shock.

Step-by-step instructions

Open the freezer and remove the shelves

1. Start by opening the freezer door and removing any items that may get in the way during the repair.
2. Remove the ice bin from the top of the ice maker.
3. Locate the ice maker arm and lift it up to the off position to prevent the ice maker from producing ice during service.
4. Remove the two shelves from the freezer.
5. Release the side trim pieces on the top shelf.
6. Lift up the left side while pushing to the right to remove it.
7. Use the same process for removing the bottom shelf.
8. At the back of the freezer, there is a cover panel held on with 1/4-inch screws.
9. Use a nut driver to remove the 6 screws holding this panel in place.
10. Lift up on the panel, being careful of the sharp edges.
11. Use a flathead screwdriver to prop it open so you can access the components behind it.

Disconnect and remove the motor

1. Locate the electrical plug connecting the evaporator fan motor wiring harness.
2. Pull firmly and disconnect it.
3. There is also a ground wire connected to a green screw terminal on the motor assembly. Remove this wire as well.
4. You can now slide out the metal bracket holding the fan motor.
5. Maneuver it out through the freezer compartment access hole.

Remove old bushings and install new ones

1. Remove the old bushings and install the new replacements.
2. Place the motor assembly on a sturdy work surface.
3. Use the flathead screwdriver to pry the fan blade off the motor shaft. Be careful not to bend the blade.
4. Locate the tab securing the mounting bracket to the motor housing. 
5. Press in on the tab and slide the bracket off. This will expose the old front bushing, allowing you to pull it off the motor shaft.
6. Turn the motor around to access the rear bushing. 
7. Remove the retaining clip and slide the old bushing off the shaft.
8. Slide the rear replacement bushing onto the shaft until it sits against the motor housing. 
9. Install the front bushing next in the same way.
10. Position the mounting bracket over the front bushing and lock it into place by pressing the retaining tab.
11. Slide the fan blade back onto the exposed end of the motor shaft, making sure it seats firmly.

Reinstall motor assembly

1. You’re now ready to put the repaired motor assembly back into the freezer compartment.
2. Carefully place the motor back into position, routing the wiring harness through the access hole.
3. Reconnect the wire harness plug and ground screw.
4. Tilt the cover panel back down into place, taking care not to pinch any wires.
5. Replace the 6 mounting screws using your 1/4-inch nut driver.

Replace shelves and ice maker

You’re in the home stretch now! 

1. Slide the bottom shelf back into position, aligning the side rail with the guides. 
2. Install the top shelf next using the same process.
3. Replace the side trim pieces onto the shelves if they were removed previously.
4. Lower the ice maker arm back down to the on position. 
5. Replace the ice bin at the top of the ice maker assembly.

Finish up

1. Plug your refrigerator back in.
2. Wait a short amount of time and confirm the evaporator fan is running quietly. 

More information

Thanks for reading! If you have any other appliance repair needs or projects, you can find more resources including our DIY blog at AppliancePartsPros.com. There, you can enter your model number to order the exact parts you need. Most orders arrive in two business days.

You can also reach our award-winning customer service team at 1-877-477-7278, chat with a pro on our website and watch thousands of free video tutorials on our YouTube channel.

Make sure to follow us on Facebook, Twitter and Instagram