How to replace GE dishwasher blower motor assembly WD26X10056

Is your GE dishwasher leaving your dishes disappointingly wet? The culprit might be a faulty blower motor assembly, but don’t reach for the phone just yet—this is a fix you can tackle yourself! Just below, you’ll find a step-by-step how-to video that breaks down everything you need to know to get your dishwasher drying perfectly once again.

If your GE dishwasher isn’t drying your dishes well, the problem may be a faulty blower motor assembly. But before you pick up the phone to call a repair technician, try replacing it yourself with this guide. We’ll walk through the entire process so you can get your dishwasher working normally again.

If you need a replacement blower motor assembly, you can order part WD26X10056 here. If you need more parts, just enter your dishwasher’s model number at AppliancePartsPros.com or visit this page.

Watch the full repair here

Why replace the blower motor assembly?

The blower motor assembly is mounted on the inside of the dishwasher door in the upper left corner. It circulates air during the drying cycle to help moisture evaporate off the dishes. If dishes come out wet at the end of the wash cycle, the blower motor assembly might be broken and need to be replaced.

Replacing this part requires separating the outer and inner dishwasher doors to access the blower motor housing. It’s not a difficult job, but does take some time and patience.

What you need

• Phillips screwdriver
• 1/4-inch socket wrench
• Small flat-blade screwdriver
• Replacement blower motor assembly WD26X10056 (use your model number to check for compatibility at AppliancePartsPros.com)

Read more: How to Wash Dishes: By Hand or By Dishwasher

Safety precautions

Your safety should always be the top priority when performing any appliance repair. Keep these tips in mind:

• Always power off and unplug your appliance or switch off the circuit breaker before attempting any maintenance or replacement work. This keeps you safe by preventing any risk of electric shock.
• If the appliance has recently been used, give it plenty of time to cool down before working on it.
• Take your time and don’t rush while working to prevent accidents and personal injuries.
• Work in a well-lit area so you can clearly see and access appliance parts.
• Keep your workspace free of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with wet hands. Make sure the work area is completely dry.
• Check the user manual to see if there are specific installation or safety instructions related to your appliance or replacement part.
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause personal injury.
• Wear insulated work gloves to protect your hands from sharp metal parts and debris.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Consider wearing safety glasses and/or a dust mask when working with chemicals, dust or a large amount of debris to prevent irritation or injury.

Replacement steps

Step 1 – Separate the outer and inner doors

1. Separate the outer and inner dishwasher doors by removing the two 1/4 inch screws – one in each of the bottom corners of the dishwasher – with a socket wrench.
2. Open the dishwasher door and remove the Phillips screws along the left and right sides of the inner door panel. Leave one screw on each side loosened, but still threaded.
3. Slightly lift up the outer door panel, supporting it from underneath as you remove the final screws.
4. Tilt the door panel upward, lift up on the handle slightly, and slide it out.
5. Fully remove the outer door panel by pressing down the release tab on the wiring harness and disconnecting the ribbon connector from the main control.
6. Set the inner door aside.

Read more: Dishwasher is Noisy: Top 6 Reasons and Fixes

Step 2 – Remove the old blower motor assembly

1. Find the blower motor assembly housing in the upper left corner of the dishwasher’s interior.
2. Disconnect the power plug by pressing the tabs on the sides and pulling apart the connector.
3. Use a Phillips screwdriver to remove the four screws securing the motor housing.
4. Slide the motor assembly out.
5. Turn the assembly over and remove the six Phillips screws holding the blower fan in place.
6. Lift off the old blower fan and set it aside.

Step 3 – Install the new blower motor assembly

1. Align the new blower motor into the plastic housing. Make sure the screw holes line up.
2. Insert and tighten the six Phillips screws with a screwdriver to tighten it in place.
3. Slide the blower motor assembly back into position in the dishwasher. Line up the screw holes and insert and tighten the four Phillips screws.
4. Plug the wiring connector back into the blower motor assembly, pressing firmly until it clicks into place.

Read more: Surprising Things That Can & Can’t Go in the Dishwasher

Step 4 – Reassemble the dishwasher

1. Orient the outer door panel correctly and hang it on the retaining brackets inside the inner door. Plug the wire from the outer door into the main control.
2. Support the door as you replace the Phillips screws on the left and right sides.
3. Partially thread the top two screws.
4. Lift the door panel slightly and remove the supporting hand.
5. Fully tighten the final two screws to secure the inner door in place.
6. Replace the two 1/4-inch screws in the bottom corners of the dishwasher.

More information

Thanks for reading! We hope this article helped you replace the blower motor assembly in your GE dishwasher.

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We have over two million parts in stock and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278. We can also help you troubleshoot common dishwasher problems here.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter, and Instagram to see our latest repair guides!