How to replace the door strike mount WD13X22837 on a GE dishwasher

Struggling with a GE dishwasher door that won’t latch shut? A faulty door strike mount might be to blame, but fear not—this is a DIY fix you can tackle with just a few tools and a bit of time. Follow along with our step-by-step guide and watch the how-to video below to get your dishwasher door closing tightly once again!

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

Got a GE dishwasher door that just won’t latch? The problem could be the door strike mount (part number WD13X22837), and luckily, it’s a pretty simple fix. If you’ve got a screwdriver and a few minutes to spare, we’ll tell you how to replace it step-by-step. Let’s get that door closing tight again—no more pushing or propping it shut!

Watch the full repair here!

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

What is the door strike mount?

The door strike mount is a plastic part inside your GE dishwasher that the door latch attaches to. Over time, this piece can become damaged or worn out, preventing your dishwasher door from closing securely. Replacing this affordable part can fix issues like the door not staying closed, water leaking from the door seal, and the dishwasher not running cycles properly.

What you’ll need

• Phillips screwdriver
• Flathead screwdriver
• 1/4 inch nut driver
• 5/16 inch nut driver
• 5/8 inch wrench
• Towels or buckets for catching water
• Wire cutters/strippers *Utility knife
• GE door strike mount replacement part (WD13X22837)

Safety precautions   

Safety should always be a priority when working on any appliance. Here are a few practical tips to help you stay safe:

• Turn off the power to the appliance by unplugging it or switching off the circuit breaker before starting any maintenance or repairs. This protects you from the risk of electric shock.
• Wear insulated gloves to shield your hands from sharp edges, pinching hazards, or debris.
• Work at a steady pace and take your time to avoid accidents or injuries.
• Make sure your workspace is well-lit so you can clearly see and access the parts you’re working on.
• Keep the area clear of clutter, and ensure children and pets stay out of the workspace.
• Never handle internal parts with wet hands. Check that both your hands and the work area are completely dry.
• Refer to your appliance’s user manual for any specific instructions or safety guidelines related to the part or repair.
• Handle parts gently to avoid damage to the appliance or potential injuries from applying too much force.
• Use safety glasses when dealing with chemicals, dust, or large debris to protect your eyes from harm.
• If the appliance was recently used, give it enough time to cool down before working on any heated components.
• Take photos or notes of wiring connections and terminals before disconnecting anything to make reassembly easier.
• Avoid touching exposed wires or terminals. If you must handle wires, use non-conductive tools or wear insulated gloves to minimize the risk of electrical shock.

Dishwasher prep

Before disassembling the dishwasher, you need to disconnect it from power and water supply lines.

1. First, make sure the dishwasher is unplugged or that the circuit breaker to the dishwasher is switched off. This eliminates the risk of electrocution as you work on the appliance.
2. Next, turn off the hot water supply valve underneath the sink that feeds water to the dishwasher. 
3. Have a towel or bucket handy to catch any water still in the fill line.

Partial dishwasher removal

1. To access the door strike mount, you’ll need to pull the dishwasher several inches out from under the counter.
2. Start by locating the water supply line and drain hose underneath the sink. 
3. Use a 5/8-inch wrench to loosen the fill line where it connects to the hot water valve. 
4. Unscrew it completely by hand and set it aside.
5. For the drain hose, use a 5/16-inch nut driver to loosen the hose clamp where it attaches to the sink drain/garbage disposal. 
6. Slide the hose off and set it in your bucket.
7. With the lines detached, open the dishwasher door and use a Phillips screwdriver to remove the screws securing the dishwasher under the counter. 
8. Carefully pull the dishwasher out several inches. You don’t need to remove it fully.

Accessing the door strike

1. With the dishwasher pulled out, use a 1/4-inch nut driver to remove the screws from the access panel on the front frame.
2. Remove the panel and insulation and set them aside.
3. Locate the wiring harness bundled on top of the dishwasher tub. 
4. Release the locking tab and unhook the harness from the tub clip. 
5. Let the harness hang loose.
6. Then, release the door cable retainers on each side. 
7. Lift the cables off the door hinge mounts and hook them into the retainers below to hold them out of the way.

Removing the dishwasher door

1. To fully remove the door, open it enough to lift the hinge pins up and out of the mounts. 
2. Pull the door assembly off the dishwasher and place it on a covered table.
3. Use a flathead screwdriver to pry off the vent cover in the door panel. 
4. Remove the two screws from each side at the base of the door with a 1/4-inch nut driver. 
5. Then use a T25 Torx bit to remove the two screws from the hinge side.
6. Carefully separate the outer panel from the inner panel and set the outer panel aside.

Removing the old strike mount

1. Use a 1/4-inch nut driver to remove all of the screws from the perimeter of the inner door panel, except for the one securing the door latch assembly. 
2. Lift out the control panel assembly and set it aside.
3. You’ll now see the plastic door strike mount. 
4. Remove the screw securing the door strike piece itself with a 1/4-inch nut driver. 
5. Lift the strike out of the way.
6. Pull the old strike mount down and out from under the metal retaining lip. 
7. Discard this part.

Installing the new strike mount

1. Set the new GE door strike mount in place under the retaining lip. 
2. Align the screw holes on the mount with the dishwasher frame.
3. Replace the door strike, inserting it into the slot on the strike mount. 
4. Install the 1/4-inch screw to secure it in place.
5. Carefully reposition the control panel assembly over the inner door panel, aligning all the screw holes. 
6. Replace the shorter 1/4 inch screws along the top and the longer screws around the sides.

Reassembling the dishwasher door

1. To reinstall the outer door panel, seat it over the inner panel, lining up the tabs and slots. 
2. Pull the outer panel tight against the inner panel as you go.
3. Use the T25 Torx bit to reinstall the two hinge side screws. 
4. Flip the door over and replace the base screws with the 1/4-inch nut driver.
5. Snap the vent cover back into place. 
6. Carefully lift the door and seat the hinge pins back into the dishwasher mounts.

Completing the repair

1. With the door replaced, reconnect the door cables by hooking them over the hinge mounts. 
2. Also, reconnect the wiring harness to the tub clip. 
3. Replace the insulation and access panel.
4. Slowly slide the dishwasher back into the opening under the counter. 
5. Reconnect the drain hose to the sink drain, tightening the hose clamp. 
6. Also, reconnect the water supply line and turn on the water.
7. Finally, use the Phillips screwdriver to reinstall the screws under the counter to secure the dishwasher. 
8. Plug it back in or turn on the breaker.
9. Run a test cycle to verify the door is closing, latching, and sealing properly. 

The door strike mount replacement should have resolved any issues you were having.

More information

Thanks for reading! If you have any other appliance repair needs or projects, you can find more resources including our DIY blog at AppliancePartsPros.com. There, you can enter your model number to order the exact parts you need. Most orders arrive in two business days.

You can also reach our award-winning customer service team at 1-877-477-7278, chat with a pro on our website and watch thousands of free video tutorials on our YouTube channel.

Make sure to follow us on Facebook, Twitter and Instagram!