How to replace KitchenAid stand mixer lift arm WP241764

Is your KitchenAid stand mixer struggling to lift its bowl, leaving your culinary creations in a bind? Don’t worry, we’ve got you covered with an easy DIY solution to restore your mixer’s functionality. Just a few simple steps, and with the help of our step-by-step how-to video below, you’ll have your mixer back in top shape in no time!

Need a part?  Search below using your appliance model number to find exactly what you need:

The lift arm on a KitchenAid stand mixer can be found inside the pedestal of the mixer and raises the bowl during the mixing process. But over time, like most appliance parts, the lift arm may become damaged or worn and may not lift the bowl properly.

But the great news is that you can make this repair yourself in just a few minutes by following the guidelines below.

If you need a replacement lift arm WP241764 for your KitchenAid stand mixer, you can use your model number to find what you’re looking for at AppliancePartsPros.com. We also have thousands of free DIY troubleshooting and repair guides to help you fix your mixer yourself.

Watch the full repair here!

Check part compatibility

Before you replace the lift arm, make sure you have an OEM part that’s compatible with your specific mixer model. To do this, you’ll need to find the appliance model number.

The model number will say MOD or Model before the numbers and is typically found on a sticker or a metal plate in one of the following locations:

• On the underside of the mixer’s base
• On the back of the mixer’s head or motor housing
• On the side of the mixer’s base

Once you’ve found the model number, write it down or take a clear photo of it for reference.

Next, visit AppliancePartsPros.com, where you can enter your model number to check if the new lift arm is compatible with your model.

Read more: Kitchenaid Stand Mixer Attachments To Try

What you’ll need

• Large Phillips ratchet
• Flathead screwdriver
• Needle nose pliers
• Roll pin punch
• Hammer or mallet
• Wood (optional)
• Towels (optional)
• Replacement lift arm

Disclaimer: The specific tools required may vary depending on the model of your appliance and the type of fasteners used on it. Always consult the user manual or refer to any specific instructions provided by the manufacturer for the recommended tools for your appliance model.

Read more: How To Clean And Maintain Your Stand Mixer

Safety precautions

When working on any appliance, remember to keep safety first. Here are some tips to keep in mind:

• Always power off and unplug your appliance or switch off the circuit breaker before you attempt any maintenance or replacement work. This keeps you safe by preventing any risk of electric shock.
• If the appliance has recently been used, give it plenty of time to cool down before working on it.
• Take your time while working to prevent accidents and personal injuries. Rushing is the enemy of precision.
• Work in a well-lit area so you can clearly see and access appliance parts.
• Keep your workspace free of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with wet hands. Make sure the work area is completely dry.
• Check the user manual to see if there are specific installation or safety instructions related to your appliance or replacement part.
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause personal injury.
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.

How to replace the lift arm

Follow these steps to swap out the lift arm on your KitchenAid stand mixer:

Step 1: Remove the old lift arm

1. Remove the beater by lifting it and turning it clockwise until you can lift it out, then set it aside.
2. Lift the bowl and pull it out.
3. Use a piece of wood or a towel on each side to hold the mixer when turning it upside down.
4. Hold the base securely and loosen the screws with the Phillips driver. Be careful not to strip the screws.
5. Once all four screws are removed, you can separate the two halves of the mixer. If the base is stuck, gently rock it back and forth to loosen it.
6. Lift the base off and set it aside.
7. Put the lift arm in the up position and remove the cotter pin.
8. Use a screwdriver to straighten the cotter pin, then use needle-nose pliers to pull it out. Set the cotter pin aside.
9. Slide the rod out of the lift arm and carefully lower the arm down.
10. Once the arm is in the down position, release it and drive out the roll pin to detach the arm from the mixer.
11. If possible, use a roll pin punch to drive the pin down through the bottom of the mixer.
12. Lift the base and remove the roll pin. Then set it aside.
13. Partially pull out the lift arm so that it can be detached.

Step 2: Install the new lift arm

1. Line up the new lift arm in the down position and make sure the roll pinhole is on the side.
2. Carefully hold the arm in place while pushing the rod through the arm. Align the hole with the roll pin hole.
3. Insert the roll pin through the aligned holes using a roll pin punch and a hammer.
4. Lift the arm that supports the bowl to raise the linkage and insert it into the lift arm.
5. Use a screwdriver to guide the arm up to prevent it from getting caught on anything.
6. Once the arm is in the up position, rotate the lift arm up and guide the arm into it.
7. Lift the arm to the lock position and insert the cotter pin. Bend the arms of the cotter pin over to lock it in place.
8. Put the lift arm in the down position.
9. Align the two halves of the mixer. Make sure the two locating pins on the base fit into the receptacles on the mixer head.
10. Lift the base and align the pins and receptacles before joining the two halves together.
11. Place the Phillips screws back in and use a wrench with the driver to tighten them down.
12. Put the bowl back on by aligning the pinholes and setting it down. Lock it in place.
13. Attach the beater by aligning the shaft with the opening and making sure the locking pin goes into the slot. Lift it into place and lock it on.
14. Plug the mixer back in and test it to check for any problems.

Read more: Why is my Kitchenaid stand mixer leaking motor grease?

Additional information

Thanks for reading! We hope this guide helped you replace the lift arm on your KitchenAid stand mixer.

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter and Instagram to see our latest repair guides!