How to replace the dual water inlet valve on a Whirlpool refrigerator

Is your Whirlpool refrigerator failing to produce ice or leaking water all over your kitchen floor? Don’t worry—there’s a simple fix! Discover how to easily replace the dual water inlet valve with our step-by-step guide and detailed how-to video below to restore your fridge’s water supply in no time.

Looking for the right part? Enter your appliance model number below to find the exact match and get your appliance running like new again!

The dual water inlet valve in a Whirlpool refrigerator is responsible for supplying water to both the icemaker and the dispenser. Over time, the solenoids in the valve may fail, resulting in a lack of water flow or water leaking on the floor. The good news is that this repair is relatively simple and should only take a few minutes to complete. By following the instructions provided in this guide, you’ll be able to replace the dual water inlet valve in your Whirlpool refrigerator and restore proper water supply to your icemaker and dispenser. So let’s get started!

Watch here: How To: Whirlpool/KitchenAid/Maytag Dual Water Inlet Valve WP67006531

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

What you’ll need

• 1/4″ nut driver
• 3/8″ wrench
• Towel 

Safety precautions

• Always power off and unplug your appliance or switch off the circuit breaker before attempting any maintenance or replacement work. This keeps you safe by preventing any risk of injury from electric shock.
• Don’t test wiring with a multimeter for live voltage if you’re unfamiliar with how to prevent short circuiting when testing. 
• When working with wires, avoid touching any exposed wires or terminals. If you need to touch a wire, use a non-conductive tool or wear insulating gloves to prevent electrical shock.
• Take your time and don’t rush while working to prevent accidents and personal injuries.
• Work in a well-lit area so you can clearly see and access the interior parts.
• Clear your workspace of clutter and other obstacles. Keep children and pets away from the work area.
• Never work on internal parts with bare wet hands. Make sure the work area is completely dry.
• Check your user manual to see if there are specific installation or safety instructions for your part or appliance. 
• Be gentle when handling or removing parts. Excessive force might damage the appliance or cause injury.
• Wear insulated work gloves to protect your hands from sharp metal parts, pinching hazards and debris.
• Wear safety glasses when working with chemicals, dust or cleaning large debris to prevent injury. 

Replacement steps

1. At the back of the refrigerator, place a towel under the valve to catch any water that may come out when the water line is removed.
2. Use a nut driver to remove the screw that holds the clamp on the waterline.
3. Once the clamp is off, use the wrench to press down on the locking collar that secures the water line and pull the line out.
4. Remove the screw that holds the water valve to the back panel. Also, remove the screws that hold the panel to the cabinet.
5. Lift the panel up and slide it out from behind the top panel.
6. Disconnect the wiring harnesses by pulling them straight out.  
7. Disconnect the water lines. There will be a quarter-inch and a 5/16-inch water line. Use the wrench to push up on the locking collar while pulling down on the water lines to remove them.
8. Once the water lines are disconnected, remove the valve from the panel.
9. Align the new valve on the bracket and push it back into place.
10. Connect the water lines by pushing them in until they bottom out to create a good seal. The 5/16-inch line goes on one side, and the quarter-inch line goes on the other side.
11. Reconnect the wiring harnesses, matching the yellow and brown wires.
12. Make sure the water valve is correctly aligned on the plate, and that the small tab is lined up.
13. Hold the valve in place and use the nut driver to insert the screw that holds the valve in place. It may require some effort to screw it in, as you need to cut the threads while putting it in.
14. Remount the panel by lifting it up so that it goes underneath the other panel and fits into the channel at the bottom.
15. Use the nut driver to insert the screws that hold the panel in place.
16. Put the waterline back in by aligning it with the valve and pushing it down until it bottoms out. Make sure there is a good seal.
17. Use the cordless nut driver to insert the screw that holds the clamp on the waterline.
18. Turn the water back on, plug the refrigerator back in, and check that it starts to cool.

Additional information

Thanks for reading! We hope this guide helped you replace the dual water inlet valve on your Whirlpool refrigerator. 

If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your new part to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter and Instagram to see our latest repair guides!