How to replace: Whirlpool washer dispenser assembly W10575334

Is your trusty Whirlpool washer acting up due to a faulty dispenser assembly? Don’t worry, it’s a common issue that can lead to leaks and detergent mishaps, but the good news is, you can fix it yourself! With just a few tools and our step-by-step guide—including a handy how-to video right below—you’ll have your washer running smoothly again in no time.

Thankfully this is a straightforward repair that you can complete in just a few minutes with some basic tools and by purchasing the W10575334 assembly from AppliancePartsPros.com. Don’t forget to use your model number to double-check its compatibility with your washing machine!

Watch the full repair here

The information in this article may not apply to your specific appliance model. We recommend consulting your manufacturer’s documentation or contact us with any questions.

What is the dispenser assembly?

The dispenser assembly in a Whirlpool washer is located in the top left corner. It holds the compartments for detergent, fabric softener, and bleach. Replacing the dispenser is an easy fix that prevents leaks and keeps your washer running smoothly.

READ MORE: Washing Machine is Leaking: Top 6 Reasons and Fixes

Why would a dispenser need to be replaced?

Over time, the dispenser plastic can become brittle and crack, which can cause leaks.

Some other reasons why the dispenser assembly needs replacing:

• Clogging: If the dispenser is so clogged with residue or mold in the detergent or fabric softener chambers that it can’t be sufficiently cleaned.
• Worn-out parts: Over time, valves, hinges and plastic components can wear out from repeated opening/closing and exposure to chemicals. This can lead to the dispenser not opening or closing properly.
• Leaking detergent or fabric softener: If leaks are coming from the dispenser, it likely means a crack or failure in the dispensing cups or tubing. Replacing the assembly should stop the leak.

READ MORE: Surprising Things That Can & Can’t Go in the Washer

How to replace dispenser assembly W10575334

What you need

• Quarter-inch nut driver
• Flat blade screwdriver
• Torx 20 screwdriver
• Phillips head screwdriver
• Pliers
• Replacement dispenser assembly (W10575334)

Keep safety first

• Turn off the washing machine and unplug it from the electrical outlet. This prevents electrocution while working.
• Turn off both hot and cold water supply valves.

Remove the old dispenser

Now that you have your tools and the new part, you’re ready to take out the old dispenser.

Detach the top panel

1. Use a quarter-inch nut driver to remove the three screws from the back of the top panel.
2. Slide the panel back and lift off.
3. Set the panel aside.

Take out the dispenser drawer

1. Pull out the dispenser drawer completely.
2. Press down on the release tab in the back and remove the drawer.

Unfasten the dispenser housing

1. Use a Torx 20 screwdriver to remove the two screws on the front of the control panel.
2. Remove the one-quarter-inch screw from the top.
3. Push back and release the dispenser from the side tabs.

Detach the dispenser tubing

1. Use pliers to slide off the tubing’s wire clamp.
2. Pull the dispenser tubing off the cracked port.

Disconnect the water inlet hoses and pull out the dispenser

1. Use pliers to compress and move the hoses’ clamps off.
2. Twist and work the hoses off the valve ports.
3. Pull the dispenser assembly completely out.

Install the new dispenser assembly

1. Press the tab to remove the drawer from the new dispenser.
2. Attach the provided inlet hoses to the water valve ports using the new hose clamps. Leave it loose for now.
3. Slide the back end under the retaining bar.
4. Connect the dispenser outlet tubing. Make sure it’s secure.
5. Position the side tabs into the slots and push back to lock the new dispenser into place.
6. Tighten the hose clamps with a quarter-inch nut driver.
7. Secure the dispenser housing to the front panel with a Torx 20 screwdriver and quarter-inch screws.

READ MORE: How to Decide What Water Temperature to Use for Laundry

Finishing touches

1. Pull out the old dispenser drawer handle and pop it into the new drawer.
2. Slide the drawer back into place.
3. Replace the top panel and screws.
4. Turn the water supply back on and check for leaks.
5. Plug the washer back in and run a test cycle.

More information

You made it! With the new dispenser assembly installed, your Whirlpool washer is ready for more laundry loads.

Thanks for reading! If you still need some replacement parts, grab your model number and head over to AppliancePartsPros.com. We offer over two million parts and most orders arrive in two business days. If you need some help with finding the right part or placing an order, you can contact our team at 1 (877) 477-7278.

While you’re waiting for your parts to arrive, you can explore our DIY blog and watch thousands of video tutorials on our YouTube channel.

Be sure to follow us on Facebook, Twitter, and Instagram to see our latest repair guides!