William Zinser March 01, 2019 for Model Number 110.42922 my front load washer shows "SUD" most of the time the last 20 minutes or so of cycle and there is no suds, and for a 56 minute wash cycle some times can take up to an hour and a half
1 Answer William, Check the wire harness/connections between the water level pressure switch and the CCU. Check or replace the air tube between the pressure switch and the drain pump connection. Reset/clear the error codes, if the problem persists replace the water level pressure switch. Read More...
Jason June 03, 2017 for Model Number 11042926203 I've tried all the do it yourself hacks for my CCU and thinking that a new unit will finally solve the dreaded F11. I've seen lots of web sites that show how to upgrade contacts and relays and am wondering if this is just an original OEM part (which will have the same problems in a few year), or if it is "newer" or has been upgraded to provide better reliability.
Gary D August 07, 2016 for Model Number 110.42936200 While washing the machine started beeping and flashing an F 11 code. The washer door remained locked. Now there are no indications of power going to the unit. I checked the outlet and there IS power. I left the washer unplugged for more than 15 minutes. After plugging it back in there is still no indication of power on the display. Its dead. Your suggestions are appreciated.
1 Answer Gary, The F11 error code would be a communication error between the main board and the motor control board. For this issue you would need to check the harness between the boards. If this checks ok then replace the main control board. Read More...
Tim January 14, 2015 for Model Number 110.42922200 When washer is plugged up it immediately locks the door and throws a GFCI protecting the circuit. I have replaced the interface and door lock. What do I look for next?
1 Answer Tim, The door lock is controlled through the main control board and this would most likely be the cause for the unit tripping the GFCI. You will also want to make sure that the unit is on a designated circuit and not a GFCI per the manufacturers recommendations. Read More...
Ace December 13, 2014 for Model Number 11042932220 Hi, my washer stops with failure mode on all cycles. I hit cancel and start and was usually finishing. For example, I have it on express wash, alarm just sounded with timer at 02, and F blinking still in wash cycle. Hit pause/ cancel and start and it restarted with 19 min. showing ,also in wash mode. Sometimes it finishes other times I have to cancel and hit drain/spin cycle. Replace board?
1 Answer Ace, The F02 error code is saying that the unit is going through a long drain. You will want to pull the lower panel from the front of the unit and access the drain pump. Check the filter assembly for being clogged as this will be the most likely cause for the issue. Read More...
Javier August 06, 2014 for Model Number Model:1104292600 Kenmore Elite HR3T. This washer machine when ran on permanent press works fine, last 36 minutes, BUT when its at the two last minutes in the final spin it begins to get full of water and then it stops and stays full of water. What is your advise? I think maybe the board is in conflict or what part do you advise is not functioning correctly so that I can purchase it. Thank you for any help you can provide.
1 Answer Javier, Based on the information provided it does sound like the control board is corrupted and would need to be replaced. The part number for the control board is 285924. Read More...
Colin L December 26, 2012 for Model Number 11042932200 My kenmore elite washer won't power up! It was working fine before I decided to move it to install new flooring but reconnecting the water supply and plugging it back in to the wall outlet. Nothing, the display won't light at all.I've tried unplugging it and leaving it sit for 5 min and hoping it would reset, still nothing. I also confirm that the water supply was connected to the right outlet. Any suggestion would be greatly appreciated.
1 Answer Hello Colin. You need to check and make sure there is power at the outlet. It sounds like the outlet for the power may be dead. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Wayne September 02, 2011 for Model Number 11042926200 My Kenmore Elite HE3T model # 11042926200 was giving me an occassional error code F-13. The dispersal motor and cam runs as soon as any wash cycle is pressed, but no water comes into the soap tray. When the diagnostic sequence is run, everything works correctly. I replaced the pressure switch first and have checked all connections over and over. Same problem each time I try it... Please help before I loose my wife to the pool boy!!! Wayne in VA 540-349-2800
1 Answer Hello Wayne. You will want to check and make sure the door lock assembly WP8182634 is working properly. If not, it will cause the problems your having. Also, check and see if there is power coming to the water valve during the cycle. If not, you will need to trace and see where your loosing power at. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...