0062440 Parts

This replacement air filter fits the engine on a generator. Air filters serve an important purpose in ensuing that dirt, dust, pollen, and other debris does not reach the combustion chamber, where it could cause damage. Instead, the filter traps and collects these contaminants. However, over time, the air filter will slowly clog with trapped debris, which will restrict airflow to the engine. This causes the engine to work harder than normal, consuming additional fuel, reducing performance, and increasing wear on internal components.Periodically, the owner will need to replace the air filter element. The frequency will vary based on use. Users should check their owner's manuals for specific change interval recommendations. To change the air filter, simply open the air filter housing, remove the old air filter, clean any debris that might have accumulated inside the box, and then install the new air filter. Close the housing when finished.This air filter is a genuine OEM part and is designed for specific Generac generators. It is sold individually.

This replacement part is a brush holder assembly intended for use in generators. This is a genuine replacement part made by Generac Generators. Brush holders in generators are use as the connecting piece between stationary wires and other moving parts. This is an important part as they conduct the electric current inside the machine so it is able to operate smoothly.A new brush holder assembly might be needed if the machine is unable to start or if it stops abruptly during use. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with generators made by Generac Generators.

This part is a replacement tri LED display. This part's intended use is to replace a broken or defective tri LED display in generators.This part is important for safe and proper equipment usage and thus should be kept in good working condition. If broken, cracked, faulty, or burnt out, this part will need to be immediately replaced with a genuine OEM replacement part. When working on or near an engine, it is important to ensure that it is powered off and completely cool before beginning any repairs.This is an authentic OEM replacement part from Generac made of high-quality materials. This tri LED display can be used with different models of generators that have been manufactured by Generac, Siemens, Honeywell, and some other brands. It is sold individually.

This crankcase gasket is a genuine Generac part, sold individually. This crankcase gasket can be used as a replacement part for a generator. The purpose of the crankcase gasket in a generator is to seal off the crankcase from possible fuel leakages or the accumulation of debris.The crankcase gasket might be subject to various forms of damage within the standard lifespan of a generator, including scrapes, punctures, tears, and dents. If any of these forms of damage occur and allow the seal maintained by the gasket to be compromised, the component should be replaced by this genuine OEM part. It is a simple replacement process that will require only basic tools to execute. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug before performing any kind of repair or replacement. This is a genuine OEM replacement, directly from the manufacturer. It is sold individually. This crankcase gasket is compatible with the following outdoor appliance brands: Generac, Centurion, Watchdog, Bryant, Carrier, Honeywell, and Siemens.

This vibration mount grommet is used on generators. The purpose of this part is to dampen the vibrations and reduce the shock inside of the generator. These grommets act as a cushion between two parts.New vibration mount grommets may be needed if there is excessive vibration with the generator. This vibration may cause an increase in noise from the unit. The user may notice clunking or banging sounds if these parts are not effectively dampening the engine's vibrations. Upon inspection, there may be physical damage to the black or silver portions of the part, in which case the part will need to be replaced. Allow time for the generator to cool down completely before attempting to replace or repair any components.This vibration mount grommet is sold individually and is an OEM part sourced directly from the manufacturer. This part is compatible with generators that are manufactured by Generac.

This part is an ATO fuse for air conditioners and generators. A fuse breaks the circuit in the event that there is a fault in the machine that results in too much current to flow. It protects the machine from damage, and will burn out when activated. It may also break due to exposure to the elements.A new fuse may be needed if there is a gap in the wire or if there is darkness inside where the fuse has burned due to an overload. The user can also use a multimeter to measure the resistance of the fuse element to determine if it has gone bad. If the fuse is replaced and immediately goes bad, additional diagnostics should be done to determine the cause.The ATO fuse is a genuine OEM part from the manufacturer and is sold individually. This fuse is compatible with air conditioners and generators that are manufactured by the Generac and Carrier brands.

This is a replacement eye hasp designed to hold the control module in place on generators. The eye hasp connects the back of the control module to the body of the generator and holds it in place with a bolt that fits through the eye. Because this part does not move, it will suffer from only minor wear and tear. The primary risk is from rust due to exposure to the elements. If the eye hasp becomes severely rusted or is damaged or lost when removing the control panel, it will need to be replaced.Replacing the eye hasp is not difficult, but will require the removal of the entire control panel from the generator. Once the module has been removed, locate the mounting point where the hasp attaches to the control module and remove the hasp. Install the replacement hasp and then reattach the control module to the generator body.This genuine OEM part is manufactured by Generac and fits several portable generators the company makes. It is sold individually.

This replacement part is a cylinder head assembly and is intended for use in different types of generators. This is a genuine replacement part made by Generac. Cylinder head assemblies are commonly found in different types of engines and are important parts to the cylinder as a whole. This part is a flat piece of metal and sits above the cylinder block. It is able to close the cylinder to create the combustion chamber. A new cylinder head assembly might be needed if the current one is visibly damaged in any way or missing. It is possible that the cylinder head become worn down over time after many years of use and is unable to properly seal the cylinder any longer. This part is a genuine OEM replacement part and is sold individually. This cylinder head assembly is sourced directly from the manufacturer to ensure that it correctly matches with the equipment.

This is a relay that is an essential component of many generators made by Generac. The main responsibility of the relay is to turn off and on the starter circuit without the need to be wired into that component. This prevents the need to use heavy-duty wires to connect components to the starter switch. A well-functioning relay can prevent electric shocks and ensure the generator stays in good shape for a longer period of time. If the relay is malfunctioning or damaged, it may cause the generator to stop operating. The relay will need to be replaced.When replacing the relay, first make sure the generator is unplugged and turned off. Basic tools and a pair of work gloves will be helpful for replacing this part. The generator will need to be disassembled to get access to the starter assembly where the relay is located. Remove the entire starter assembly and replace the relay before reassembling the generator. Make sure to test the tool before further use.This relay is made to be compatible with several generators made by Generac. It is a genuine OEM replacement component that is directly sourced from the manufacturer. The component is sold as an individual item.