110C69692800 Parts

This is a replacement mounting nut that secures appliance components and helps keep panels, assemblies and fasteners tight for stable operation. A simple, OEM-fit nut for repair or maintenance. What it does

• Fastens and secures assemblies, brackets or panels to prevent loosening during use
• Helps reduce vibration and rattling caused by loose hardware
• Restores proper component alignment when a stripped or missing nut causes movement
• Fits in the same location and function as the original factory nut

• Inspect the mating bolt/stud and threads; replace damaged hardware before installing the nut
• Tighten to the appliance manufacturer's specified torque where available; avoid over-tightening
• Use hand tools appropriate for the nut size to prevent rounding the hex
• Disconnect power or follow manufacturer safety instructions before servicing electrical appliances

This lower cabinet base replaces a worn or damaged support panel that stabilizes the appliance and houses lower components. Restoring the base improves cabinet alignment and helps prevent vibration and under-cabinet damage. What it does:

• Supports the appliance frame and internal components to maintain proper alignment
• Protects lower access areas from debris and moisture
• Reduces vibration and rocking caused by cracks or breaks in the original base
• Common symptom: appliance sits unevenly, wobbles, or has visible cracks or separation at the bottom edge

• Disconnect power (and gas if applicable) before beginning any repair
• Support the appliance to prevent tipping or movement when removing panels
• Remove lower access panels and fasteners to replace the base; keep hardware for reuse

The Motor Drive is an OEM part for Whirlpool electric dryers. Located behind the drum, the motor drive contains the electric motor that powers the tumbling and spinning actions of the dryer drum during each cycle. It precisely controls the amount of torque needed to adequately dry wet loads within the preset time parameters.

Symptoms of a bad motor drive include:

• The dryer drum fails to spin or rotates slowly 
• Abnormal noises coming from the back of the dryer
• The dryer takes an extremely long time to finish cycles
• Bulging, cracked, or worn belts around the motor pulley

While heavy loads and continuous usage will eventually wear down motor drives, other causes could be shocks that damage internal mechanisms or failures in motor regulation components over multiple years of heating and cooling. Replacing the drive with a new OEM part restores dependable drying performance. This replacement is also suitable for models from Maytag, Jenn-Air, Amana, Roper, and more.
 

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This screw is a genuine replacement fastener used to secure appliance panels and components for a reliable fit. It restores proper fastening where original screws are missing, stripped, or damaged. What it does:

• Fastens panels, trim, brackets or small components to keep parts aligned and secure
• Replaces missing or damaged screws that can cause loose panels or rattling
• Restores proper clamping force to prevent movement and wear on adjacent parts
• Matches OEM function and fit when the correct part number is used

• Disconnect power and water before servicing the appliance
• Use the correct driver to engage the head cleanly and avoid stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic

This lint duct assembly routes air and lint from the dryer drum to the lint trap and exhaust, helping maintain proper airflow for efficient drying. It replaces damaged or cracked ducts that can restrict ventilation. What it does:

• Channels airflow from the drum to the lint screen and exhaust
• Guides lint toward the lint trap to help prevent buildup in the cabinet
• Restores proper venting when the original duct is cracked, warped, or broken
• Helps reduce symptoms like longer dry times, excessive lint in the cabinet, or unusual dryer noises

• Disconnect power (and gas supply if applicable) before servicing.
• Access typically requires removing the dryer front or top panel—follow your model's service manual.
• Inspect and clean nearby lint seals and the lint trap area while replacing the duct.

This terminal block cover protects the dryer/range terminal block and wiring by keeping connections enclosed and reducing risk of accidental contact or debris intrusion. It restores a finished, safe rear electrical access area. What it does:

• Covers and shields the appliance's electrical terminal block to help prevent accidental contact with live wires
• Helps keep dust, lint and small debris out of the terminal area
• Provides a mounting surface for the terminal block screw or clamp where applicable
• Common service symptom: missing, cracked or damaged cover exposes wiring or looks broken at the rear access

• One terminal block cover

• Disconnect all power at the breaker or unplug the appliance before servicing
• Intended to mount over the terminal block; secure with the factory screw(s) or fastener(s)
• Inspect wiring and terminal connections while the cover is off; replace frayed or damaged wires before reinstalling

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

This top panel replaces the appliance's cabinet top to restore a flush, secure surface and protect internal components. It's a direct-fit exterior panel used when the existing top is dented, bent, or damaged. What it does:

• Covers and protects the washer/dryer cabinet and internal components from debris and spills
• Provides the mounting surface for controls, console, and trim
• Restores a straight, even appearance when the original top is warped or dented
• Helps maintain proper alignment of adjoining panels and doors

• 1 top panel

• Unplug the appliance or disconnect power before starting work
• Keep fasteners organized and hand-tighten before final torque to ensure proper fit

A duct collar that connects and secures the dryer's exhaust duct to the appliance, helping channel hot, moist air safely out of the dryer. Replaces a damaged or loose collar to restore a tight vent connection. What it does

• Provides a secure connection point between the dryer and the exhaust duct to help direct airflow out of the appliance.
• Helps reduce vent leaks that can cause poor drying performance or excess lint buildup in the cabinet/closet.
• Restores proper duct alignment to reduce rattling or vibration from a loose duct connection.
• Used when the existing collar is cracked, bent, corroded, or no longer holds the duct firmly.

• One duct collar.

• Always disconnect electrical power before servicing the dryer.
• Clean lint from the vent path before installing the new collar to ensure good airflow and reduce fire risk.
• Installation typically requires basic hand tools and a clamp or screws to secure the duct; follow the dryer's service instructions.

A small replacement retainer clip that secures interior panels and trim to restore proper fit and reduce vibration or rattling. Fits where a molded or snap-in fastener has worn or broken. What it does

• Secures panels, trim pieces, or wiring harnesses so parts sit flush and stable.
• Prevents rattling and vibration caused by loose or missing fasteners.
• Helps keep seals and gaskets aligned by holding adjacent trim in place.
• Common symptom: loose trim, gaps, or intermittent rattling sound during operation.

• The clip shown.

• Disconnect power (unplug appliance or turn off breaker) before servicing.
• Access the clip location by removing the appropriate trim or panel.
• Clip typically snaps into a mounting hole or slot; align and press until it seats securely.
• Use basic hand tools as needed; wear gloves and eye protection to avoid injury from sharp edges.

This replacement wire harness connects electrical components to restore reliable power and signal paths in select Whirlpool appliances. Use it to replace a damaged or worn harness that causes intermittent operation or loss of function. What it does:

• Routes power and signal connections between appliance controls and components
• Replaces frayed, melted, or broken wiring that can cause intermittent operation
• Helps resolve symptoms such as no power to a circuit, intermittent operation, or control errors
• Ensures proper connector fit to maintain electrical continuity

• Disconnect power (unplug appliance or turn off circuit breaker) before starting any repair
• Verify connector orientation and routing against the service diagram before removing the old harness
• Secure harness away from pinch points and moving parts; avoid contact with sharp edges or heat sources

The Top is an OEM replacement part for Whirlpool dryers. It serves as the protective cover for the top of the dryer, keeping dust and debris out while providing a finished look. It is designed to withstand the demands of daily use and provides a sturdy surface for placing items on top of the dryer.

A bad dryer top panel can occur due to physical damage, wear and tear, or improper installation. If you notice symptoms such as a cracked or broken panel, misalignment, or an unattractive appearance, it may be time to replace the top panel.

Symptoms of a bad dryer top panel include:

• Cracked or broken panel
• Misalignment or uneven surface
• Unattractive or worn-out appearance

Restore your dryer by replacing the faulty or damaged top panel with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.